您要查找的是不是：
- Thecoating is made by using an oxy-acetylene flame spraying process. 涂层采用氧-乙炔火焰喷焊工艺制成。
- Ni-based and Co-based alloy coatings were made on the Q235 steel substrate by oxy-acetylene flame spraying and fusing. 采用氧乙炔火焰喷熔法在Q235钢表面制备了镍基和钴基合金涂层。
- In order to enhance its wear resistance,the oxygen-ethyne flame spraying method was utilized to prepare the Co-based WC composite coating on the worn guide piece. 为提高导卫板的耐磨性,采用氧-乙炔火焰喷涂的方法在其磨损表面喷熔钴基WC涂层。
- Using SHS Reactive Flame Spraying (RFS) technology, an Al2O3 multi-phased ceramic coating was prepared on iron substrate with Al and CuO as main reactants, the SHS process was ignited by oxyacetylene flame. 基于自蔓延高温合成技术(SHS)的反应火焰喷涂技术,用氧?乙炔火焰引燃Al?CuO团聚粉,使之发生自蔓延反应,在钢基表面制备了Al2O3复相陶瓷涂层。
- Results:The results show that plasma spraying can create the coatihg with finer microstructure,lower impurities content,less air hole and higher bonding strength than flame spraying. 结果:等离子喷涂与火焰喷涂相比具有涂层组织致密,杂质含量和气孔率低、涂层与基体间结合强度较高等优点。
- By means of oxyacetylene flame spraying and selection of different coating , surface adhesion factor of automobile drum type machine are improved, thus resulting in the maximum efficiency of vehicle drive moment. 以氧乙炔火焰喷涂工艺与选择喷涂层为手段,着力于提高汽车试验台转鼓表面附着系数,以获取汽车驱动力矩最大效能。
- To improve the wear resistance of the 20 steel,the oxygen-ethyne flame spraying technique was employed to prepare the Co-base WC composite spraying-welding coatings with different WC contents. 为提高20钢的耐磨料磨损性能,利用氧-乙炔火焰喷涂的方法制备了不同WC含量的钴基WC复合喷熔层。
- high velocity flame spraying(HVFS) 高速火焰喷涂
- high velocity oxy - fuel flame spraying 超音速火焰喷涂
- oxygen-acetylen flame spraying coating 氧-乙炔火焰喷涂涂层
- High velocity oxy-fuel flame spraying 超音速火焰喷涂
- High Velocity Flame Spraying( HVFS ) 高速火焰喷涂（HVFS）
- BSP-1 flame spray gun (implement type) and thermal spray plastic powder is experimentally studied. 对BSP-1型火焰塑粉喷枪(改进型)及热喷涂用塑粉、工艺进行了研究。
- The anatase contents in P25, ST-41 and liquid flame sprayed TiO2 powders were 85%, 100% and 95%, respectively. P25粉末、ST-41粉末及液料火焰喷涂粉末中锐钛矿相含量分别为85%25、100%25和95%25。
- The cold end of the SER element is flame sprayed with aluminum for a distance of about two inches. 对冷端部进行喷铝是要保持大约两英寸的距离。
- The Application of Flame Spraying in Antenna Frame Manufacture 火焰喷镀工艺在天线骨架制造中的应用
- Powder flame spray and spray fusig gun, with various powder nozzles attached, can do spray coating with fine metallic powder and ceramic powder. 粉末火焰喷涂喷焊设备,配有各种粉末喷嘴,能喷涂金属微细粉末和氧化物涂层。
- Study on the Technology of Flame Spraying Glass Coatings 火焰喷涂玻璃涂层工艺研究
- Powder flame spray or spray fusing gun can be used with inert gas to feed powder with best coating effects,and can also be used for spary of ceramic powder. 粉末火焰喷涂喷焊设备。用惰性气体送粉，能得到更佳涂层品质，也可喷涂氧化物涂层。
- Keywords SHS;reactive flame spraying;ceramic coating;mechanism; 反应火焰喷涂;陶瓷涂层;机理;
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
