您要查找的是不是：
- minimum film forming temperature 最低成膜温度
- Minimum Film Forming Temperature of Emulsion and Its Influencing Factors 乳液的最低成膜温度及其影响因素
- Influence factors of minimum film forming temperature of styrene-acrylate polymer emulsion 苯丙乳液的最低成膜温度及其影响因素分析
- Keywords waterborne polyurethane;epoxy resin;MMA;core-shell crosslinking;minimum film forming temperature（MFT）; 水性聚氨酯;环氧树脂改性;丙烯酸酯改性;核壳交联;最低成膜温度（MFT）;
- Keywords Dispersity Particle size distribution Minimum film forming temperature; 多分散;粒径分布;最低成膜温度;
- Synthesis and Characterization of Waterborne Polyurethane Dispersion with Low VOC Content and Low Film Forming Temperature 低VOC低成膜温度水性聚氨酯分散体的合成与表征
- Influence of Polymerization Technology and Monomer Ratio on the Minimum Film Forming Temperature of Vinyl Ace-tate/Styrene/Acrylic Emulsion/ 聚合工艺和单体配比对醋苯丙乳液最低成膜温度的影响
- The influence of particle size, film - forming temperature and other factors on the CPVC is discussed. 讨论了乳液的粒径大小、成膜温度等因素对CPVC的影响。
- The influence of density, total acidity and phosphorated temperature of film forming material on ph... 文中论述了成膜物质的浓度、总酸度、磷化温度等条件对磷化膜的影响。
- A thin film formed on the surface of the pulp. 纸浆表面结了一层膜。
- BPA/DEG (hydroxy) is 1/2 and use it as the chain extender prepared room temperature film forming one-component anion waterbome polyurethane waterproof coating. 以BPA/DEG(羟基)为1/2作为混合扩链剂,可制得室温成膜单组分阴离子型水性聚氨酯防水涂料。
- The thin, dry film formed by such a mixture when applied to a surface. 已干油漆层用于表面时这种混合物薄而干的膜
- And the film forming and their properties of latexes were also invesitgated. 考察了复合乳液的成膜性及胶膜性质。
- The super-plastic forming process of bearing cage in variety forming temperature and total forming time was simulated with finite element method. 利用有限元法对轴承保持架在不同成形温度和总成形时间下的超塑成形进行了数值模拟。
- EDX analyses showed the adsorbed film formed on the cast iron. X-射线能谱分析显示在铸铁的摩擦表面有一吸附层形成。
- The character and development of isothermal forging process,its forming temperature and forming rate for titanium alloy is introduced in this paper. 本文介绍了钛合金等温锻造技术的特点,国内外钛合金等温锻造的发展及其成形温度和变形程度等工艺。
- The reason is that the bionically unsmoothed surface has better ability on lube storage and oil film forming. 其原因是在有润滑条件时，仿生非光滑结构具有较强的贮存润滑油及形成油膜的能力。
- The phosphorated fluid mainly consists of film forming agent, promoter and additive. 磷化液主要由成膜剂、促进剂及添加剂组成。
- The thin,dry film formed by such a mixture when applied to a surface. 已干油漆层用于表面时这种混合物薄而干的膜
- The binder emulsion exhibits fairly good in film forming, printing behaviour, colour fastness and hand feeling. 该粘合剂的乳液、成膜、印花性能及牢度和手感均为良好。
