您要查找的是不是：
- filler metal layer 钎料层
- Aerospace series - Gold base alloy AU-B40001 - Filler metal for brazing - Wire. 航空航天系列.;金基合金AU-B40001
- They are readily weldable, in most cases, with or without filler metal. 多数此种合金可焊（不论加或不加焊料金属）。
- This paper only details the processing of vectorization of metal layer images. 本文主要以集成电路芯片上的金属图形为例，来讨论其矢量化过程。
- However, for attaching nonpressure parts to pressure parts, the filler metal chemistry shall match the nominal chemistry of the pressure part. 但将非受压元件焊接受压元件时所用的填充金属，应与受压元件的标称化学组成相配。
- Influence of Sn and In in silver filler metal on spreadability and joint strength is studied. 研究了银基钎料中元素锡、铟对钎料铺展性能和接头的影响,分析了钎料的显微组织和锡、铟在钎料中的作用机理。
- Cold lap is a condition where the weld filler metal does not properly fuse with the base metal or the previous weld pass material (interpass cold lap). 冷隔？（未熔合）由于熔敷金属没有很好的与母材熔合或没与前道焊缝熔合（层间未熔合）。
- One should cover the resistance with metal layer, to avoid the damaged during the wafer level testing. 用金属覆盖电阻,避免wafer级测试时的损伤。
- The next step is to apply a metal layer on top of the embossed pits or wobbled groove. 下一个步骤是在塑料基片的浮雕坑型或摆动槽的上面覆盖一个金属层。
- Abstract: In this paper, the mechanism of electrochemistry corrosion of the tractor radiator brazed with brass (H90 and H70) and Sn-Pb filler metal was investigated. 文摘:研究了采用黄铜(H90、H70)和锡铅钎料钎焊而成的拖拉机水箱电化学腐蚀机理。
- The metal layer was described in distributing, thickness and visage by the method of EPMA. 利用电子探针分析了在不同条件下 ;环氧树脂表面所沉积的金属层的形貌、表面成分和金属沉积层厚度 .
- It adopt advanced jointing technique when joint the valve and the copper tube，it brazing filler metal well，without pore and overheating，and has a smooth make and break . 阀体与铜管的连接，采用先进的焊接工艺，钎料到位，无气孔和过烧现象，开闭灵活。
- The thickness of metal layer can be confirmed by admittance loci illustrate method. 应用导纳轨迹图解方法,可以确定能诱导出滤光片最大透射率的金属层厚度。
- The mechanical properties of welding and weldment have been conduct on X80 pipeline steel under the selection of welding process, welding filler metal and parameter. 摘要在选定焊接方法、焊接材料和工艺参数条件下，进行了X80管线钢试件焊接和接头性能试验。
- Spot checks contractor piping isometrics or fabrication drawings showing weld procedures， filler metal， pre-heat and post-weld heat requirements and monitors their use. 抽检承包商的管道轴侧图和预制图中关于焊接程序、填料、预热和焊后热处理的要求并监督其实施情况；
- In this paper, the mechanism of electrochemistry corrosion of the tractor radiator brazed with brass (H90 and H70) and Sn-Pb filler metal was investigated. 研究了采用黄铜(H90、H70)和锡铅钎料钎焊而成的拖拉机水箱电化学腐蚀机理。
- In the deep submicrometer design, with the increase of metal layer and the reduced width of line, the circuit performance and density have been improved greatly. 摘要集成电路设计进入了超深亚微米领域，金属层增加，线宽减小，使电路的性能和密度都得到了很大的提高，但也引入了愈来愈严重的互连线效应，并最终引发了信号完整性问题。
- This paper introduced the sheet metal layered incremental forming process. 摘要本文介绍了金属板材分层渐进成形技术。
- THE PRESENT SITUATION AND ANALYSIS OF EXTRUSION TECHNOLOGY FOR BRAZING FILLER METALS IN THE WORLD. 国外硬钎料挤压技术的现状与分析。
