您要查找的是不是:
- fiber surface adhesion force 纤维表面粘附力
- Keywords Surface adhesion force;Atomic Force Microscope (AFM);Octadecyltrichlorosilane (OTS);Self-assembled monolayer; 表面粘滞力;原子力显微镜(AFM);十八烷基三氯硅烷(OTS);自组装单分子膜;
- Changes of the Surface Adhesion Forces during the Formation of OTS Self-Assembled Monolayer Investigated by AFM OTS自组装单分子膜形成过程的AFM研究
- The contribution of the guide surface roughness overshadows that of the fiber surface roughness. 导纱杆表面粗糙度的作用超过纤维表面的粗糙度。
- There also exists much fiber surface damage brought about by beaters, card clothing, faller pins, etc. 打手、钢丝布和梳针等金属机件都会损伤纤维表面。
- Results The adhesion force and cohesive strength could be affected by the contents of sodium polyacrylate,PVA,Gelatin. 结果配方中各因素对粘着力、剥离强度的作用大小依次为聚丙烯酸钠、聚乙烯醇、明胶。
- Of good adhesive force and washing resistance. 具有优异的附着力与耐磨性良好。
- Study on the Surface Adhesion of UHMWPE Fiber 超高相对分子质量聚乙烯纤维的表面粘结性能研究
- Oil paint has a strong adhesive force with wood. 油漆在木材表面的附着力很强。
- Results showed that there was remarkable etching on the fiber surface, which turned out grafting and precipitation so that the adhesion between fibers and the ruhber matrix was increased rubber consolidation was heightened. 结果表明,纤维表面有明显刻蚀现象,并产生接枝和沉积作用、因而增大了纤维与橡胶基质的粘合力、提高了短纤维对橡胶的补强效果。
- The following remarks refer to the effects of mechanical processing on fiber surface geometry. 下面介绍机械加工对纤维表面几何形状的影响。
- Treatment with Tong Xin Luo Capsule,however,both adhesion force and adhesion stress were markedly reduced ( P <0.05 or P <0.01). 加通心络胶囊后 ;细胞粘附力和粘附应力均明显下降 (P <0 .;0 5或P <0
- This means they contain no ingredients that will negatively affect surface adhesion when spraying fresh paint, or- just as important- that contaminate the paint shop environment. 意思是当你在喷漆时,他们不包含那些起反作用的成分,或者重要的是,污染物会浸蚀进车漆内部。
- Back then, 40 and 50 years ago, if the surface wasn抰 properly prepared, residual silicones on the surface or in the shop environment, could cause surface adhesion problems. 回过头来,在40-50年前,如果漆面看起来不好,即在表面上留有硅树脂或者在购买时没有发现问题,它会导致一系列问题。
- However, there exists also much fiber surface damage brought about by beaters, card clothing, faller pins, etc. 此外,打手,钢丝布和梳针等金属机件都会损伤纤维。
- The process of laser coating of super fine ceramic powder is discussed, and the hardness, roughness and adhesion force to the substrate of the coating are investigated. 介绍了激光熔覆陶瓷粉的工艺过程,并对熔覆层的硬度、粗糙度和熔覆与基底之间的结合情况进行了考察。
- Friction increases with increasing fiber surface roughness in the boundary and semiboundary. 在边界和半边界区内,摩擦随纤维表面粗糙度的增加而增加。
- What the primer I use is Japan's French grey powdery paint surface primer, the goal is covers the original design and the reliable paint surface adhesion. 底漆我用的是日本的浅灰色粉末状漆面底漆,目的是遮盖原图案和牢固漆面的附着力。
- Notice:Heating Cylinder must clean and non-pollut when use temperature is Abov Highest limitation on long time,The Hot Meet Adhesine Shale be lase Adhesion force. 注意事项:加热料筒必须清洁无杂质,若使用沾度长期超出最高极限时,该热熔胶将会失去粘合力。
- ESEM images indicated that fibrils were present on the fiber surface after synergistic treatment. 纤维素酶、半纤维素酶与漆酶/介体处理后,纤维表面出现细小纤维。