您要查找的是不是:
- Breaking Strength The amount of force needed to break a wire or fiber. 断裂强度将电线或电缆折断所需施加的压力。
- The breaking strength and elongation decreased as the degree of oxidation of cotton fiber increased. 氧化棉纤维的断裂强度和断裂伸长率随氧化程度的提高不断降低。
- The breaking strength and elongation decreased as the degree of oxidation of cotton fiber i... 氧化棉纤维的断裂强度和断裂伸长率随氧化程度的提高不断降低。
- The melting point of the fiber was decreased and the breaking strength and birefraction were decreased to a minimum first- ly and then incr. 随着拉伸温度的提高,纤维的熔点降低,断裂强度和双折射率则先降低后升高,出现最低值。
- The properties including bulging rate,breaking elongation rate and breaking strength of the jute fiber were tested under the different conditions. 分别测定了不同工艺条件下黄麻纤维的膨化率、断裂伸长率、断裂强力的变化。
- The xerothermic properties of vinylon-milk protein fiber were studied,including shrinkage,whiteness,breaking strength,weight loss and dyeing behaviors. 研究维纶基牛奶纤维纱线经不同温度干热处理后,纱线收缩率、白度、断裂强力、失重率以及染色性能的变化。
- Used to determine the tensile breaking strength, extension at break of single yarns such as cotton, wool, linen, silk, chemical fiber and so on. 用于测定棉、毛、麻、丝、化纤等单根纱线的抗拉断裂强力、断裂伸长。
- Used for measure breaking strength, elong rate of all kinds of fibre materials. 用于测定各种材料的机织物、非机织物的断裂强力、断裂伸长率。
- Used for measure breaking strength,elong rate of all kinds of fibre materials. 用于测定各种材料的机织、物非机织物的断裂伸长率。
- The paper mainly studied the air - jet textured processing for twisted glass fiber yarn, and analysed the effects of the chief parameters on the texturing and breaking strength of the textured yarn. 主要研究玻璃纤维有捻长丝纱的变形制造工艺及工艺参数对变形纱变形效果和断裂强度影响。
- When the fibers broke, fiber ends were mangled and frayed. 纤维断裂时,纤维端部相互纠缠并有擦散现象。
- Bacterial enzymes are also preferred for the desirable end product qualities of porosity and breaking strength. 细菌性酶也适于生产多孔性及易碎的产品。
- Breaking strength: The quality of paper by specifying its breaking length in metre. 裂断强度:以纸张的裂断长(米)来表达纸张品质。
- A meso mechanical model is developed to describe the longitudinal stiffness reduction and thermo dilatation variation of the composites caused by fiber breaking or fiber peeling o. 借助细观力学模型,研究了纤维断裂和剥离对宿主材料刚度和热膨胀系数的影响,并给出了相应的数学表达式。
- Choosing raw materials, spunlaced process properly may improve product cross breaking strength effectually. 选择适当的原料、水刺工艺参数可有效地改善产品的横向断裂强力。
- The writer explained that cross lapping and impregnated method may improve product cross breaking strength. 说明了采用交叉铺网、浸胶的方法可大大提高产品的横向断裂强力;
- In this paper,the methods are discussed on improvement breaking strength of synthetic libers in processing stage. 根据合成纤维生产工艺过程,分析了合成纤维断裂强度提高的途径。
- The breaking strength of cotton fabric will drop evidently both in warp and weft after anti crease finishing. 全棉织物经免烫整理后,其经纬向断裂强力明显下降。
- Moreover,the relation between AE signals and the failure processes of FWC from matrix cracks,delaminations,fiber breaks to burst with the water pressure increasing is analyzed. 分析了随着水压增加从基体开裂、层间分层及纤维断裂到最终破坏与声发射信号的关系;
- There are changes in mechanical properties of the fabric such as weight, thickness, stiffness, permeability, or breaking strength and elongation. 有织物机械性能的改变,诸如重量,厚度,硬度,透气,断裂强力和伸长度等性能的改变。