您要查找的是不是：
- factory test pressure 工厂测试压力
- Each completed and assembled motor shall receive a routine factory test. 每一台装配完好的电机都应该接受常规的工厂测试。
- All models are certified at 300 PSI test pressure and 150 PSI working pressure. 所有型号都通过300PSI试验压力检验和150PSI工作压力检验。
- GIN Factory Test Pilots wanted a wing with nice dynamic handling, good for fun and tricks, smooth and light, precise in the turn, thermal biting. 试飞员们的目标是设计出一款拥有出色的空气动力学性能，轻便，平稳，转向精确，良好的气流攀升性能的双人伞！
- All Oil-Powered water heaters are certified at 300 PSI test pressure and 150 PSI working pressure. 所有燃油热水器都通过300psi(2068kPa)实验压力和150psi(1034kPa)工作压力检测。
- This test pressure includes corrections for service conditions e.g. backpressure or high temperatures. 此试验压力包括工作条件如：背压和高温的校正值。
- It is suitable in computer network project、electronic instruments、armarium、research institute、measurement and test device、factory test board and so on. 适用于电脑网络工程、家用电器、医疗设备、科研单位、测试、测量设备、工厂校验台等设备配套使用。
- Items of factory test to KMB series of DC switchgear are designed.Conclusions and analyses to kinds of problems are done according to the running and operative situation. 针对现场运行及调试情况，对直流开关柜故障类型加以总结和分析，并提出相应解决措施，使设备更好的服务于供电系统。
- According to the test pressure and nominal pressure of pipes,calculated and compared their numerical value. 结合管材测试压力和公称压力,计算并比较了它们之间的数值。
- The TK-DL can test pressure vacuum breakers, reduced pressure backflow preventers or double check valve assemblies. TK-DL可以检测压力真空断路阀，减压防回流阀或双止回阀总成。
- Please rest assured that all HTC devices are factory tested before released. 请放心，HTC的设备出厂前都经过充分测试，十分安全。
- Cold differential test pressure the pressure at which a valve is set on a test rig using a test fluid at ambient temperature. 冷差试验压力（或冷态差分试验压力）：在此压力下，阀门固定在试验台上，用一试验流体于室温下作试验。
- Pressurisation should be suspended at intervals on the way up to the test pressure to allow time for inspection to find leaks. 在达到测试压力之前的增压过程中应有间歇暂停时间，以便进行检查，以发现有无泄漏。
- Data were analyzed by ANOVA factorial tests. 数据用方差分析阶乘测试法分析。
- Hose corrugation deformation will occur if the maximum rated working pressure is multiplied by 150% to determine the maximum rated test pressure. 波纹软管变形会出现，如果最大额定工作压力乘以150 %25 ，以确定试验压力最大额定。
- It is now our aim to set up a factory. 我们现在的目的是创办一座工厂。
- Each motor is fully factory tested prior to shipment to guarantee operation within NEMA standards on routine tests. 在出厂之前，每台电机在制造中心都经过全面的检测，以确保在常规测试中，能够符合NEMA标准。
- Our precision test gauges with mirrored scale are manufactured with highest precision and are used to test pressure in research and development and in laboratories. 我们的高精度校验表是根据最高标准生产的,用于研究和开发部门以及实验室的压力校验。
- In experimental measurement, F P laser interferometry and auto measurement system are used to take F P interference pictures and test pressure distributions. 实验测试应用F－P激光干涉仪和自动测压系统，得到流场F－P干涉照片和压强分布。
- Normal service relief valves, expansion bellows and any other fittings not designed for the full test pressure, must be removed or positively isolated from the system. 必须将正常操作卸压阀、膨胀波纹管和任何其它未经设计用于满压测试的管件拆除或与测试系统完全隔离开。
