您要查找的是不是:
- Neural network method was used to investigate the parison swell affected by the die temperature and extrusion flow rate. 采用神经网络方法预测了受模口温度和挤出流率影响的型坯成型阶段的膨胀。
- extrusion flow rate 出料速度
- The large diameter mesophase pitch carbon monofiber in uniform size was obtained by controlling the matching of extrusion flow and drawing rate. 熔纺时控制了挤出流量和牵伸速率的良好匹配,获得了丝径均匀的大直径中间相沥青炭单丝。
- Consistent flow rate from nebulizer to nebulizer. 在雾化器间提供持续稳定的流通速率。
- Affect the melt flow rate and the cooling speed. 会影响熔体的流动性和冷却速度。
- Possibility to control the flow rate by Pump. 由蠕动泵调节盐溶流量。
- Factors influencing the graft ratio and melt flow rate of LDPE were studied based on the melt extrusion of methyl acrylic acid (MAA)grated onto LDPE. 通过聚乙烯熔融挤出接枝甲基丙烯酸(MAA),研究了各种因素对LDPE接枝率及熔体流动速率的影响。
- Typical maximum system flow rate (7.5 feet/sec. 标准最大系统流量为7.;5英尺/秒。
- The HTA flow rate has two-faced influences on them. 热风流量对其影响呈现两面性。
- Either flow rate is insufficient or CPU is overoccupied. 不是流量不够用就是CPU资源占用过多!
- Detection wavelength was 260 nm,flow rate 0.7 mL/min. 检测波长2 6 0nm ; 流速为 0 .;7mL/min。
- How the Catering Enterprises Face a High Employee Flow Rate? 员工流动率高餐饮企业如何面对?
- Average flow rate (AFR) adds from 3.42ml/s to 9.89 ml/s. 平均尿流率(AFR)从3 .;4ml/s增至9
- Turn on the carrier gas, and establish the proper flow rate. 接通载气,调至合适地流速。
- Decreasing the gas flow rate leads to pressure undershoot. 气量突降时,膨胀波沿程传播。
- The dynamic rheological behavior and non-isothermal cold crystallization of poly(ethylene terephthalate)(PET)were studied to reflect the disentanglement effect of the pulsatile extrusion flow field. 通过分析PET熔体的动态流变参数和结晶动力学过程的变化,间接证实动态挤出聚合物熔体分子的解缠结作用。
- Effect of absorbent flow rate on CO2 absorption is unobvious. 吸收剂流量对CO2吸收过程没有明显的影响。
- The experimental results show that die pressure of PA6 and PA6/HDPE blends is reduced remarkably in the presence of ultrasonic wave during extrusion, but the melt temperature and mass flow rate of PA6/HDPE get increased. 在PA6/HDPE体系的超声挤出过程中,超声辐照所提供的能量场作用、高频剪切振动会导致共混物熔体口模温度升高、口模压力降低、挤出产量提高,因此,超声辐照能有效改善共混体系的加工性能。
- Read horizontally to flow rate curve and vertically downward to flow rate gpm. 读出水平线上的流量曲线和垂直线下方的的流量(加仑/分钟)。
- The test is designed to determine the flow rate of the reactor coolant pump. 试验是设计用来确定反应堆冷冻剂泵的流速。