您要查找的是不是：
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm，冷却时间便占10.;8秒。
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm，冷却时间是76.;8秒。
- When chilled water is used to cool the mould, cycle time is related to wall thickness as follows. 在冰水冷却的条件下，冷却时间与壁厚有以下的关系。
- The aorta wall thickness (AWT) was measured wiht B-mode echocardiography in 128 patients with primary hypertension. B型超声心动图下测量了128例高血压病患者主动脉壁厚度（AWT），同时检测了血脂指标。
- Centrifugal casting, compact structure, free from pinhole porosity and slag, smooth surface and even wall thickness. 高速离心铸造,组织致密,无砂眼、夹渣,表面光滑、壁厚均匀。
- The carotid intima-media wall thickness (IMT), crouse score and plaque incidence were measured. 测量颈总动脉后壁内中膜厚度(IMT),斑块厚度,计算斑块积分及粥样斑块发生率。
- The serum apolipoprotein (apo) level, aorta wall thickness (AWT)and ocular fundus were simutaneously examinated. 同时进行血清载脂蛋白（apo）、主动脉壁厚度（AWT）及眼底检查。
- The wall thickness of the hollow aeroengine turbine blade is a critical parameter for ensuring its strength. 航空发动机空心涡轮叶片的壁厚是保证叶片强度的一个关键参数。
- Movement is powered by hidden electric motors on ‘bogeys' integrated into the wall thickness. 运动是由电动机的隐藏'忌'融入壁厚。
- It was virtually difficult to distinguish between benignancy and malignancy by the wall thickness alone. 有关病灶之良性或恶性与否，单藉胃壁增厚程度的多寡很难加以鑑别。
- The needed pipe bending moment、wall thickness reduction and ovality of section are known by simulating. 通过模拟,计算管子弯曲变形所需的弯矩,计算管子弯曲部分外壁减薄率和椭圆度。
- A dime is equivalent to ten pennies. 一角等于十分。
- A calculating formula of the relationship between beam gap and parison wall thickness is presented. 重新推导出该间隔与型坯壁厚之间的计算公式。
