您要查找的是不是：
- emergency DC power raising 直流紧急功率提升
- emergency DC power support 紧急直流功率支援
- Operation From DC Power Supply: Batteries. 使用直流电源：干电池。
- This paper base on the design of 28V600A DC power. 介绍以28V600A直流电源设计为背景。
- CBF series are able to be applied to large current DC power line. CBF系列的晶片能够应用于大电流的直流电源信号线.
- AC or DC Power: 500mA peak start-up current for 10 msec. 交流或直流电源： 500mA峰值启动电流为10毫秒。max.;马克斯。
- Specially designed for suppressing DC power line disturbances. 专为抑制直流电源线干扰而设计.
- The 125 volt DC power system supplies power to the low draft trip switches. 应翻译为125伏特直流电源系统为低负压跳车开关供电。
- If necessary,plug the DC power supply cord into the WinAIP Interface Box and the power supply into an AC outlet. 如果必要，将 DC 电源线插入 WinAIP Interface Box，并将电源插到 AC 插座上。
- On the condition without DC power, the SCR could be used to realize dynamic braking. 在无法取得直流电源的情况下，利用可控硅元件，也可实现能耗制动。
- This dc power supply offers high performance and precision measurements in a one-box solution. 这个直流电源供应器以单机解决方案,提供了高效能与精确的量测。
- The ideal power amplifier would be supplied pure DC power ONLY from the power supply. 理想的功放是纯直流电源供应只是供电。
- If necessary, plug the DC power supply cord into the WinAIP Interface Box and the power supply into an AC outlet. 如果必要，将 DC 电源线插入 WinAIP Interface Box，并将电源插到 AC 插座上。
- When applied with DC power supply,the tool is compatible with single conductor cable,used to log GR+CCL+CBL. 在直流供电时 ,该仪器可配接单芯电缆 ,完成GR +CCL +CBL固放磁测井。
- The objective of DC power modulation is to damp the relative swing of angle and frequency of the two areas from COI. 直流输电线路功率调制的目标是阻尼区域COI功角和频率间的相互振荡。
- Use a rubber grommet when passing the DC power cable through a metal plate to prevent a short circuit. 当将直流电源电缆穿过金属板时，请用橡胶皮圈进行隔离，以防放生短路。
- That's when the DC power supply is being added to the load, which is broken when power supply was disconnected. 通的时候即是直流供电被加到负载上的时候，断的时候即是供电被断开的时候。
- The difference between actual output of this DC power and predefined value is below 1% in the test. 经过测试，该直流电源的实际输出与设定值之间的误差小于1%25，达到设计要求。
- The only access points for transients are via the AC or DC power line wires and all of the data and telcom signal wiring that enters and leaves the cabinet. 电涌的唯一进入通道是交流或直流电源线及所有进出金属箱的数据线和信号线。
- Power input types are: AC power (220 VAC or 110 VAC), DC power supply (commonly used for the 24 VDC). 电源输入类型有：交流电源（220VAC或110VAC），直流电源（常用的为24VDC）。
