您要查找的是不是：
- elastic - plastic FEM analysis 弹塑性有限元分析
- A large deformation elastic plastic FEM model is employed to simulate the stretch flanging of V shaped sheet metal parts. 采用弹塑性大变形有限元方法研究了几何形状和材料参数对“V”型零件翻边的影响;
- The results of FEM analysis coincide quite well with the measuring results. 通过热模拟实验实测，表明计算结果与实测值相符合。
- The densification and deformation behavior of pure aluminum by powder metallurgy during the ECAP process was studied by compressible rigid plastic FEM. 针对纯铝粉末多孔材料,采用可压缩刚塑性有限元法对其等径角挤压过程进行数值模拟,并着重分析了静水压力对挤压效果的影响。
- The forming process of 6400 steering knuckle arms was analyzed by plastic FEM software Deform. The reasons causing the problems of fold and underfill in the production were found. 使用塑性有限元分析软件deform对 640 0转向节臂成形过程进行了模拟分析 ,找出了其在生产过程中出现的折叠、缺肉等问题的原因。
- Combined with the complexity of 3D FEM analysis of seepage field of underground project, the simulation of faultage was comprehensively discussed. 摘要结合地下工程渗流场三维有限元分析复杂性的实际，对断层的处理进行积极探讨。
- The clamping schemes of thin-walled package were discussed on the base of FEM analysis. 摘要采用有限元分析方法，对薄壁件的装夹方案进行了讨论。
- The clamping schemes of thinwalled package were discussed on the base of FEM analysis. 采用有限元分析方法,对薄壁件的装夹方案进行了讨论。
- FEM analysis software of DYNAFORM was used to simulate the bending form for the support. 运用DYNAFORM有限元数值模拟分析软件,对汽车转向柱后支架的弯曲成形进行了数值模拟。
- Stresses in supporting structure and the retained soil in foundation pit are analyzed with elasto - plastic FEM, and the active limiting displacement of supporting structure was calculated with "artificial participation" optimization. 运用弹塑性有限元程序计算基坑支护结构和土体的应力状态,采用“人工参与”的优化法来研究当基坑支护结构偏离土体方向时使土体达到主动极限平衡时的主动极限位移。
- FEM analysis of the extrusion-forging process for an automobile knuckle is also introduced. 针对汽车转向节的挤压锻造进行的有限元分析。
- Abstract: When plastic FEM is used to numerically simulate the process of sheet metal forming, handling of dynamic contact interface conditions between the workpiece and its dies is needed to obtain credible computational results. 文摘:采用塑性有限元法对金属板料成形过程进行数值模拟时，为获得可信的计算结果，需要对工件与模具间动态接触边界条件进行处理。
- When plastic FEM is used to numerically simulate the process of sheet metal forming, handling of dynamic contact interface conditions between the workpiece and its dies is needed to obtain credible computational results. 采用塑性有限元法对金属板料成形过程进行数值模拟时，为获得可信的计算结果，需要对工件与模具间动态接触边界条件进行处理。
- Based upon element by element(EBE) iterative strategies,a feedback multi layer neural model is proposed for the heat conduct problem FEM analysis. 基于Element By Element(EBE)策略 ,提出了一种反馈网络和前向网络共同组成的多层神经网络以实现热传导有限元分析。
- FEM analysis of a kind BRB applicable to space structures was conducted by using software ANSYS.The hysteresis curve of the BRB was obtained. 摘要利用ANSYS程序对一种适用于网壳结构的屈曲约束支撑进行有限元分析，得到支撑的滞回曲线。
- The proposed method is also applicable to the FEM analysis of conrete structures such as bridges post-prestressed with uncoated curve tendons. 该方法还适用于有黏结曲线预应力筋的预应力混凝土结构有限元计算。
- Experiment and FEM analysis for one bridge was finished,and the current technique of test and calculation for mchanical character was summarized. 对某桥梁进行了实测和理论分析，概述了它的力学特性测试及分析计算的现有技术。
- N.H.Nan, C.C.Huang , “The FEM Analysis for LCD module of Clammer-type Handset during Drop,” BenQ Corporation,Mobile BG,2004. 林信昌“手机落槌测试与结构分析”，逢甲大学机械工程所，硕士论文，2004。
- Two specimens at full scale of bidirectional pin-hinged joint in the Guangzhou new TV tower were tested using FEM analysis. 摘要对广州新电视塔钢结构双向铰节点进行了两个典型节点足尺试验研究和有限元分析。
- At the same time, the basic datas and feasible waies for the FEM analysis of the steel structure of the whole contact system are provided. 同时,也为整个接触网系统的钢结构有限元分析系统研究提供了基础数据和可行的方法。
