您要查找的是不是:
- Dynamic Finite Element Model of Giant Magnetostrictive Transducer 超磁致伸缩换能器有限元动态模型的研究
- Due to complicated configuration and multi control surfaces,the flutter characteristic design of T-tail is complicated and there are many parameters in the process of establishing dynamics finite element model,so the designers face more difficulties. T型尾翼构型复杂;操纵面多;在动气动弹性的有限元建模和颤振特性设计中;需要修改的参数多;颤振分析复杂;设计人员面临很大的困难.
- Dynamic finite element model updating using meta-model and genetic algorithm 一种利用等效模型与遗传算法的动态有限元模型修正方法
- Dynamic Finite Element Model Updating And Its Application in Aerospace Structures 动态有限元模型修正技术及其在航空航天结构中的应用
- Dynamic finite element model 动态有限元模型
- Its finite element model is established. 构造了其有限元模型。
- The Updating of Dynamic Finite Element Models for the Compound Cam-Linkages Machine 凸轮弹性连杆复合机构的动力学修改
- A Rotor Dynamics'Finite Element Model with Consideration of the Influential Effect of the Fluid 考虑流体作用的转子动力学有限元模型
- A static finite element model of an air spring was given. 摘要文中建立了空气弹簧的静态有限元模型。
- With engineering concrete example, based on spacial finite element model, the effect of dynamic property by LRB of girder and arch combination bridge is discussed. 结合工程实例桥,基于空间有限元模型,系统讨论了铅销橡胶支座对梁拱组合桥梁动力特性的影响。
- The work proves the validity of the finite element model of the engine and paves the way to further research of the engine's dynamic simulation. 从而说明所建立的整机的有限元模型是正确可靠的,为整机结构进一步的动态仿真研究奠定了基础。
- Thus, the validity of the finite element model of the engine was proved, which paves the way for further engine dynamic simulation research. 从而说明所建立的整机的有限元模型是正确可靠的,为整机结构进一步的动态仿真研究奠定了基础。
- The finite element model of an undamaged 3-story experimental frame model is firstly updated based on the measured dynamic information by using neural network method. 摘要首先建立了三层试验框架结构的有限元模型,利用未损伤状态的动态测量数据,采用神经网络方法分步对原结构的有限元模型进行了修正。
- The dynamic finite element program of bonded prestressed concrete beams was designed. 本文对有粘结预应力混凝土简支梁进行动力有限元程序设计。
- A two-dimensional dynamic finite element analysis is made of the deflection information by using FORTRAN. 在研究弯沉盆信息时,利用FORTRAN程序进行了轴对称模型的动力有限元分析。
- The finite element model of opening gap tantalum thin-walled tube is setup. 为了控制钽薄壁管焊接成形的质量,进行钽薄壁管开口间隙场计算模型的研究。
- A finite element model describing the drawing process of the heat-shield panel of automobile engine is established by using the commercial dynamic explicit code LS-DYNA. 摘要使用基于动态显式算法的商业软件LS-DYNA建立了某汽车发动机隔热罩拉延成形的有限元模型,通过所建立的有限元模型分析了压边力对拉延成形的影响。
- Split Hopkinson pressure bar (SHPB) tests on C100 and C80 concrete specimens were simulated with explicit dynamic finite element software LS-DYNA. 摘要用显式动力有限元软件LS-DYNA,模拟C100与C80高强混凝土SHPB试验过程。
- Objective: To discuss a method about shaping a dynamic and visualizational color stress cloud chart of finite element model of Ni-Ti arch wire for orthodontics. 目的:探讨形成镍钛弓丝有限元模型动态可视化应力云图的方法。
- This paper uses ANSYS/LS-DYNA of dynamic finite element software to analyse dynamic response of buried gas pipelines caused by rockfall impact. 本文利用ANSYS/LS-DYNA动力有限元软件分析了落石冲击作用下埋地输气管道的动力响应。