您要查找的是不是:
- Design of Digital Position Servo Control System 数字位置伺服控制系统设计
- Design of Full Digital Position Servo System 全数字位置随动系统设计
- digital position servo 数字式位置伺服机构
- DC motor position servo system is an important component of the digital speed governor system utilized on natural gas engine. 直流电机位置伺服系统是天然气发动机电子调速系统的关键组成部分。
- This paper proposes a position servo system based on digital brushless DC motor using TMS320LF2407A Digital Signal Processor (DSP). 摘要基于TMS320LF2407A,建立了无刷直流电机全数字控制系统。
- The hardware design and control tactic of the position servo system. 介绍了系统的硬件设计及控制策略。
- Electromechanical Position Servo System (EPSS) is a kind of automatic system used widely. 机电位置伺服系统是一种应用极为广泛的自动化系统。
- This paper presents a digitized DC motor position servo control system based on DSP. 提出一种基于数字信号处理器(DSP)的全数字直流位置伺服控制系统。
- An arithmetically negative carry. It occurs in performing subtraction when the subtrahend is larger than the minuend in a particular digit position. 一种算术负进位,它出现在某一特定的数位上减数大于被减数的减法运算中。
- At last, it establishes RBF neural network based on the electro-hydraulic position servo system, and the results prove the description hereinbefore. 最后以仿真电液位置伺服系统为例,建立相关的RBF网络,验证以上的陈述。
- Based on the Permanent-Magnet Synchronous Motor(PMSM) vector control,the control of position servo system is achieved by using repetitive control(RC). 在永磁同步电机矢量控制的基础上,利用重复控制策略对位置伺服系统进行了控制。
- The equivalent load observed is fed back for resisting force load disturbance and raising the accur acy of the hydraulic position servo control. 利用观测出来的等效负载进行反馈控制,抑制力负载干扰的影响,提高液压位置伺服控制的精度。
- This paper proposes a state feedback control strategy with a neural network compensator,which is applied in a hydraulic position servo system. 提出一种具有神经网络补偿的状态反馈控制方法并用于液压伺服位置控制系统。
- The experiment indicates that the system is suitable,and the digital position detection circuit composed with the resolver and AU6802N1 is feasible. 实验结果表明,系统设计合理,旋转变压器和AU6802N1组成的数字位置检测电路正确可行。
- In the paper,stepping position servo system is introduced in the thesis,and the system s controlling scheme and its structure are analyzed detailedly. 详细地分析了步进式位置伺服系统控制方案及其软硬件结构设计。
- The 16-bits single-chip computer (89C196KC) and resolver are used to realize the position servo control of antenna pointing system. 系统采用89C196KC单片机和多极旋转变压器实现了卫星天线指向系统的位置伺服控制。
- A digit position within a set of digits corresponding to a given power of the radix. 在对应于给定的基数幂次的一组数字中的一个数字的位置(简称数位)。
- An operation resulting in the reverse significance in each digit position in a series of digits. 一种对一串数字中每一位数都求反变成其相反意义的数的运算。
- A DC position servo controller used for the laser machine CNC system is introduced which is based on a 80C196 single chip mleroprocessor and made on the industrial PC bus board. 本文介绍一种用于激光加工数控系统的工业PC总线模板式80C196单片机直流位置伺服控制器。
- Aimed at discrete model for pneumatic position servo system, investigation of time-delay and noise polynomial was carried out for improving its control accuracy. 摘要为提高气动位置伺服系统的控制精度,针对其离散模型,分别对时延数和噪声多项式进行研究。