您要查找的是不是：
- differential amplified circuit 差分放大电路
- Several Mistakes in Using Equivalent Transformation to Analyze Differential Amplifier Circuit with Single Input 等效变换法分析单端输入差动放大电路的几个误区
- differential amplifier circuit 差动放大电路
- The amplifier circuit is nonlinear circuit. 放大线路是非线性电路。
- The conditioning cir-cuit consists of a differential amplifier and a flip-flop circuit. 结果表明,开关性能良好,工作点合理,达到设计要求。
- It is the equivalent circuit of a triode amplifier circuit. 它是三极管放大器的等效电路。
- The PGA consists of the differential amplifier with variable source degeneration resistor and the DC-offset correction circuit. 该可编程增益放大器采用源极反馈电阻可变的差分放大器结构,且带有直流漂移校正电路。
- It is the equivalent circuit of a triode amplifier circuit . 它是三极管放大器的等效电路。
- Magnetic field changes are sensed by two integrated Hall transducers and then are differentially amplified on the chip. 磁场变化可由两个集成霍尔传感器检测到,然后再在芯片上进行差分放大。
- Then we design a fully differential amplifier combined with a third order Butterworth Sallen-Key low-pass filter. 因此在信号处理电路部分设计一个差动放大电路串接一个三阶的低通滤波器。
- In this situation, the CMRR (common-mode rejection ratio) of the input differential amplifier was unsatisfactory. 在这种情况下，输入差分放大器的CMRR（共模抑制比）不令人满意。
- Some kinds of linear amplifier utilize a tube as a load element in the amplifier circuit. 有的利用各种管道作为线性放大器负载的放大器电路组成。
- Simple differential amplifiers drive directly into the transformer, and the receive signal is measured across a single 100 ohm resistor (“balance”). 简单微分放大器直接打入变压器内，接收信号通过一个单个100欧姆的电阻（“平衡”）来测试。
- This paper introduces the design of a linear photoelectric isolating amplifier circuit, and analyzes the errors of the circuit in experiment. 摘要对所设计的线性光电隔离放大电路做一介绍，并对电路进行了误差分析及实验研究。
- This common-mode biasing can be achieved using the on-chip differential amplifier, further reducing the external signal conditioning requirements. 此共模偏置可利用片内差分放大器来实现，从而可进一步降低外部信号调理要求。
- He amplified his remarks with drawings and figures. 他用图示和数字进一步阐明他讲的话。
- The suitable amplifying circuit and analog to digital circuit are also importance to ensure the measuring accuracy. 测量电路中放大器和模／数转换电路的合理设计是保证测量精度的另一个设计关键。
- This common mode biasing can be achieved using the on-chip differential amplifiers, further reducing the external signal conditioning requirements. 此共模偏置可利用片内差分放大器来实现,从而可进一步降低外部信号调理要求。
- The transistor amplifier circuit is provided with an oscillation preventing countermeasure. 晶体管放大电路配备了一个过电压保护装置。
- It has the advantages of differential amplifiers, such as lower drift and higher CMRR. Both input terminals and output terminals were electrically isolated as well. 这种放大器具有低温度漂移、高共模抑制比等差动放大器的优点,同时输入端与输出端之间也是电隔离的。
