您要查找的是不是：
- deflection curve equation 挠曲线方程
- THE FINITE DEFLECTION CURVE EQUATIONS AND STIFFNESS OF OUTEXTENDING LADDER AXLE 外伸阶梯轴的有限挠度方程及刚度分析
- The deflection curve is a sinusoidal for the rod with a zero self-weight. 自重为零时，杆轴线为半个正弦曲线；
- The height curve equation h=a 0d a1 was most accordant the pattern of height with DBH. 对树高曲线方程而言 ,h=a0 da1 最符合火炬松树高随直径变化的规律。
- Approximately differential equation of the deflection curve 挠曲轴近似微分方程
- The impact of covariates on diagnostic test assessment can be deducted adopting the methods of ROC curve equation. 利用ROC曲线方程,可以扣除协变量对诊断试验结果评价的影响,并能够计算出在不同协变量取值下的ROC曲线下面积,提供更为丰富和可靠的信息。
- According to real tested data,it builds up CVC cambering curve equation by polynomial regression. 根据实测数据,采用多项式回归方法,建立CVC辊形曲线方程,并探讨了该方程的重要实际意义。
- The method suggested in this paper is that we remove all the intermediate supports and obtain an essential statically determinate system and then find the deflection curve of the beam by means of a power series. 本文提供的方法是:去除中间支座以得基本静定系统,然后借助于幂级数求解梁的挠曲线。
- The connected curve equation after spreading connected joint of taper container are derived, the new blanking method with computer is put forward. 导出了圆锥形容器接管交线在展开接管表面后的曲线方程，提出了用计算机绘制其交线，即放样下料的新方法。
- With variation of shearing angles, the strength curve equation of thenardite and calcium thenardite salt rocks are deduced. 另外，由变角剪切试验结果分别获得了无水芒硝和钙质芒硝岩盐的强度曲线方程。
- Based on the tooth profile curve equation of inner rotors in cycloidal pump, the formula for displacement calculation of the pump are derived. 根据摆线泵内转子的齿廓曲线方程,推导出了摆线泵的排量计算公式。
- The load versus mid-height deflection curves of the composite member can be divided into three stages, i.e. 试件的载荷-中截面挠度曲线可以分为以下三个阶段：弹性段、弹塑性段和软化段。
- Based on production decline curve equation, through mathematical derivation, a kind of logarithmic type production decline curve equation is obtained. 在产量衰减曲线方程的基础上，通过数学推导，得到了一种对数型产量衰减曲线方程。
- The section curve equation of main stirring shaft is obtained by deducting the screw profile curve formation process of the stirring kneader. 摘要用数学方法对搅拌捏合机搅拌轴螺杆外形曲线的形成过程进行了详细的推导，得出了主搅拌轴截面曲线形状公式。
- The connected curve equation after spreading connected joint of taper container are derived，the new blanking method with computer is put forward. 导出了圆锥形容器接管交线在展开接管表面后的曲线方程，提出了用计算机绘制其交线，即放样下料的新方法。
- Based on Arps decline curve equation this paper presents the autoregressive model for analyzing the production exponential decline curve, the analysis is convenient and reliable. 本文基于Arps递减曲线方程，提出了油气田产量指数递减曲线分析的自 回归模型。
- load-middle span deflection curve 荷载-跨中挠度曲线
- A mechanics model for constant supporting spring hangers is put forward.Then from the working principle of constant hanger, the curve equation of cams is induced. 摘要建立恒力弹簧支吊架的力学模型，并根据恒力弹簧支吊架的工作机理，推导其凸轮的曲线微分方程。
- One kind of beam type gas injection packing support plate used in the column is introduced. The curve equation of the developed pattern of the arciform plate is presented. 介绍了塔器内梁型气体喷射式填料支承及其拱形板展开图,并通过详细计算给出了该展开图的曲线方程。
- Based on the test results, the ultimate load-carrying capacity, mode of failure, cracking behavior and load versus mid-pan lateral deflection curves of the strengthened specimens are summarized and analyzed. 在试验的基础上，对加固构件的极限承载力、破坏形态、裂缝分布以及荷载－跨中桡度曲线等进行了总结和分析。
