您要查找的是不是:
- cylinder wall thickness 汽缸壁厚度
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- Shape optimization was used to optimize the thickness of the cylinder wall, taking mass reduction as the objective and the maximum stress being below the original one as the constraint. 应用形状优化对曲轴箱两侧壁面的厚度进行优化,以减重为优化目标,以最大应力不超过原缸体应力为约束条件。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- It is equipped with piston rings to provide a good seal between the cylinder wall and piston. 上面装有活塞环,从而使活塞和气缸壁之间具有良好的密封性。
- The adjusting mechanism of the frictional resistance between the filler and cylinder wall,and between the subsoil and cylinder wall is discussed. 采用模型试验,以实测筒内、外土压力和筒底压力为依据,探讨内填料和地基土与圆筒筒壁间摩阻力的调整及其变化规律。
- Considered the diffusion of liquid in the cylinder wall, an equivalent constitutive equation of osteon in the longitudinal direction was obtained. 并考虑了液体在筒壁内的扩散,从而得到了骨单元沿轴向的等效本构方程。
- Parks J,Armfield J,Storey J,et al.In Situ Measurement ofFuel Absorption into the Cylinder Wall Oil Film During EngineCold Start[C].SAE Paper,No.981054. 刘圣华;赵慧;周龙保;李继军.;缸套壁面润滑油膜其对汽油机未燃碳氢排放影响的研究[J]
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- Traditionally,the seal between the regenerator and cylinder wall has been accomplished using sliding bearings,but there was contact and wear in the bearings. 传统的回热器使用接触式滑动密封,存在磨损,限制制冷机的使用寿命。
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm,冷却时间便占10.;8秒。
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm,冷却时间是76.;8秒。
- When chilled water is used to cool the mould, cycle time is related to wall thickness as follows. 在冰水冷却的条件下,冷却时间与壁厚有以下的关系。
- The aorta wall thickness (AWT) was measured wiht B-mode echocardiography in 128 patients with primary hypertension. B型超声心动图下测量了128例高血压病患者主动脉壁厚度(AWT),同时检测了血脂指标。
- In this system, cylinder walls are lubricated by splashing oil thrown off from the connecting-rod bearings. 在这一系统中;汽缸壁是由连杆轴承运动飞溅起来的油进行润滑的.
- Centrifugal casting, compact structure, free from pinhole porosity and slag, smooth surface and even wall thickness. 高速离心铸造,组织致密,无砂眼、夹渣,表面光滑、壁厚均匀。