您要查找的是不是:
- cylinder wall temperature 汽缸壁温度
- Tells FDS to record the wall temperature of all solid surfaces. &BNDF QUANTITY='WALL_TEMPERATURE' / 告诉FDS 记录全部固体表面的墙温度。
- Stainless steel single and double wall temperature control containers. 不锈钢容器及带温控夹套砂磨筒。
- It is equipped with piston rings to provide a good seal between the cylinder wall and piston. 上面装有活塞环,从而使活塞和气缸壁之间具有良好的密封性。
- Cylinder wall surface temperature transducer 汽缸壁表面温度发送器
- The adjusting mechanism of the frictional resistance between the filler and cylinder wall,and between the subsoil and cylinder wall is discussed. 采用模型试验,以实测筒内、外土压力和筒底压力为依据,探讨内填料和地基土与圆筒筒壁间摩阻力的调整及其变化规律。
- Considered the diffusion of liquid in the cylinder wall, an equivalent constitutive equation of osteon in the longitudinal direction was obtained. 并考虑了液体在筒壁内的扩散,从而得到了骨单元沿轴向的等效本构方程。
- Parks J,Armfield J,Storey J,et al.In Situ Measurement ofFuel Absorption into the Cylinder Wall Oil Film During EngineCold Start[C].SAE Paper,No.981054. 刘圣华;赵慧;周龙保;李继军.;缸套壁面润滑油膜其对汽油机未燃碳氢排放影响的研究[J]
- The infrared radiation and wall temperature were obviously decreased by cooling. 通过冷却,各喷管的壁温和红外辐射强度明显降低。
- Traditionally,the seal between the regenerator and cylinder wall has been accomplished using sliding bearings,but there was contact and wear in the bearings. 传统的回热器使用接触式滑动密封,存在磨损,限制制冷机的使用寿命。
- The amplitude of wall temperature fluctuation is larger than that of fluid temperature oscillation. 流量的波动又引起了管壁温度和流体温度的周期性波动;
- From the curves of wall temperature vs axial length , the location of dryout points were obtained. 由壁温随长度的变化曲线得到干涸点产生的位置。
- The wall temperature,collapsed liquid level and liquid carryover transient are measured. 试验表明,再淹没过程中,定位格架下游的元件表面温度明显下降,骤冷前,定位格架下游的传热系数比上游高,特定工况下,可高出70%25,定位格架对传热的影响程度随试验参数及距骤冷前沿位置的不同而不同;
- The wall temperature distribution is tested on an annular combustor by using thermocouple and temperature-indicating paint. 壁温分布试验在全环形燃烧室试验台上进行,采用热电偶和示温漆测量。
- The piston is essentially a cylindrical plug that moves up and down in the engine cylinder. It is equipped with piston rings to provide a good seal between the cylinder wall and piston. 实质上活塞是一个在气缸中上下移动的圓筒状的塞子。上面装有活塞环,从而使活塞和气缸壁之间具有良好的密封性。
- The heat losses and wall temperature under steady heat conduction of Fiber linings in enamelling furnace are calculated and analysed. 分析计算了在稳态导热情况下搪烧炉纤维炉衬不同结构时的散热量和外壁温度,给出了炉衬经济厚度的计算公式和计算方法。
- In this system, cylinder walls are lubricated by splashing oil thrown off from the connecting-rod bearings. 在这一系统中;汽缸壁是由连杆轴承运动飞溅起来的油进行润滑的.
- The wall temperature distributionin different impinging jet heigtht are given,as well as sensitivity and accuracy of the technology arediscussed. 文中给出了在不同射流高度下壁面温度分布的等值线,并讨论了液晶测温技术的灵敏度及测试精度。
- Even slight traces of grit or dust left on the cylinder walls may cause rapid ring and wall wear and early engine failure. 残留在气缸壁上的砂砾或尘埃所造成的划痕,均能引起活塞环和气缸壁的迅速磨损以及发动机的早期损坏。
- The wall temperature of combustion section for an afterburner is significantly related to the safety of an aircraft and aeroengine. 加力燃烧室燃烧段的壁温对飞机和发动机的安全关系重大,单靠数值计算是很不够的,目前主要靠测试取得。