您要查找的是不是：
- cylinder bore diameter 气缸内径
- Single plane mean bore diameter deviation. 单一平面平均内径偏差。
- Bore diameter variation in a single radial plane. 单一径向平面内径变动量。
- Reciprocating pumps convert rotary motion to linear motion. Pump speed in rpm determines the pumps output volume for any given combination of cylinder bore and piston stroke. 循环泵将曲轴旋转运动转化为柱塞的直线运动。泵速转每分钟决定了任何气缸和活塞组合的排泵量。
- The size identification for Y-bearing units is the bore diameter of the incorporated Y-bearing. Y-轴承单元的尺寸代号表示所含Y-轴承的内径。
- The bore diameter and width of the IR inner rings are made to Normal tolerances in accordance with ISO 492:2002. 根据2002年的ISO 492标准,IR内圈的孔径和宽度以普通级公差制造。
- In diesel engine industry, the development of small cylinder bore and several cylinder bores diesel engine and spare parts is supported. 内燃机行业，支持发展小缸径、多缸径柴油机及零部件。
- Hot load and mechanical load coupling make piston to produce crackle, piston-ring glued and scuffing of cylinder bore and so on. 热负荷和机械负荷耦合将导致活塞产生裂纹、活塞环胶结以及拉缸等。
- The tested solenoid has a bore diameter of 400 mm, stored energy of 0.445 MJ and a peak field of about 5 T. 被试磁体内径400mm、储能0.;445MJ;峰值磁场约5T
- There are no many vessels whose bore diameter is small in the root, and no ray in the xylem. 根中导管数量少，孔径小，次生木质部不含射线。
- The different functions and cutting thicknesses in the boring process of hydraulic cylinder bore with four cutting tools fitted on one spindle are presen ted. 一根刀杆上四种切削刀具在液压缸内孔加工过程中的不同功能及不同切削用量;
- In most engines, do not overbore more than .030", or localized heating of the water jacket may occur, not to mention a twisting cylinder bore under hard engine loads. 在大多数发动机;不要否决了超过.;030”;或局部加热水的夹克;更不用说一个扭载荷下的发动机气缸孔难。
- The influence of throttle bore diameter and melt temperature in internal ladle on constituent distribution, marco-structure androckwell hardness of the casting was investigated. 研究了节流孔径和内浇包熔体温度两个工艺参数对铸件的成分分布、宏观组织和洛氏硬度的影响。
- Vsing this tool to process small bore diameter chilled steel,not only has high process accuracy,stabilizes process quality,but also raises tools using lifetime. 采用此刀具加工小直径淬火钢内孔,不仅加工精度高、加工质量稳定,又能大大提高刀具的使用寿命。
- The stroke of cylinder bearing with compressing loading is controlled by buckling strength. 承受压缩负载的油缸的行程通过压曲强度来控制。
- Push the glove box lock cylinder firmly into the lock cylinder bore while rotating the key and cylinder counterclockwise to the 6 o'clock position, where the lock cylinder retaining tumbler will snap back into place. 将手套箱锁柱压入锁柱孔，同时逆时针旋转钥匙和锁柱至六点钟位置，这样锁柱定位卡簧将弹回原处。
- Push the glove box lock cylinder firmly into the lock cylinder bore while rotating the key and cylinder counterclockwise to the6 o' position, where the lock cylinder retaining tumbler will snap back into place. 将手套箱锁柱压入锁柱孔，同时逆时针旋转钥匙和锁柱至六点钟位置，这样锁柱定位卡簧将弹回原处。
- Bearings up to and including 300 mm bore diameter are produced to higher precision than the ISO Normal tolerances. 孔径达(含)300mm的轴承的制造,使用比ISO正常公差更高的精确度。
- The honed crosshatch pattern in the cylinder bore acts like a file to allow the rings to wear.The rings quickly wear down the "peaks" of this roughness, regardless of how hard the engine is run. 被珩磨成刀路相互交叉的油缸内孔像一把锉刀去摩擦密封环，密封环很快就将各高点磨掉，这与狠用发动机没有关系。
- Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。
