您要查找的是不是:
- Prolonging curing time may lower the crosslinking density. 硫化温度的提高会使交联密度下降。
- You can shorten the curing time and the cycle of molding. 因其热硬化的速度较快,所以可缩短成型时间。
- The using and curing time decreased with the increasing of accelerant amount. 促进剂少,适用期变长,同时固化时间也会变长。
- Curing Time: The time needed to complete curing of an epoxy at a certain temperature. 固化时间:环氧树脂在特定温度下完全固化所需要的时间。
- The dose of accelerator BPP can mainly affect the curing time and can affected the workability more or less. 促进剂BPP的用量主要影响胶料的硫化时间,对加工性能有一定的影响;
- The gel time and the curing time depend on the mixed volume, the temperature and the thickness of the layer. 凝胶时间和固化时间要根据混合量,温度和层数的厚度来定。最终性能取决于固化水平。
- The curing time and the resistance after curing rise a little more with the thickness increasing. 随着导电胶层厚度增加,固化时间和固化后的最低电阻都有一定的增大;
- Dan Zufen moisture curing, the curing time is not reduced, good flexibility, and strong anti-deformation. 单组份有机硅湿气固化,固化时不收缩,弹性佳,抗形变能力强。
- The influence of the curing time on the structure and properties of SBR ebonite was investigated. 研究硫化时间对硬质SBR结构与性能的影响。
- The effect of the curing time、temperature and the thickness of ECA for electrical conductivity of ECA was researched. 研究了固化温度、时间及导电胶层厚度对导电胶固化后导电性的影响。
- Testing showed that the curing time,adhesive strength,water resistance and heat resistance were all improved greatly. 产物的表干时间、粘接强度、耐热耐水性得到较大改善。
- The effect of rolling condition and O/P value of phenolic resin on the curing time and flowability of phenolic resin for injection molding was studied. 考察了辊压工艺及酚醛树脂的邻对位比值(O/P)对酚醛注塑料的成型时间及流动性的影响。
- Dan Zufen silicone extrusions moisture curing, the curing time is not reduced, good flexibility, and strong anti-deformation. 单组份有机硅湿气固化,固化时不收缩,弹性佳,抗形变能力强。
- The results showed that the modification of PF resin with lac was doable,the curing time of the lac modified PF resin was ap... 因此,用紫胶改性酚醛树脂胶粘剂是可行的。
- The effects of types and doses of intensifier,curing temperature,and curing time on intensity of the consolidating body were investigated. 为将声波速度应用于注浆质量检测中 ,就声波速度与注浆固结体单轴抗压强度之间的关系进行了研究。
- Effects of graphite content,curing time and curing temperature on the properties of the composite were studied with orthogonal test. 采用正交试验方法研究了石墨含量、固化时间以及固化温度对复合材料的影响。
- By properly reducing the content of curing agent,TMTD,adjusting the curing time and avoiding post curing,the best TMTD content of 0. 通过减少硫化剂TMTD,调整硫化时间,控制和防止后硫化,解决了燃气发生器的以丁腈橡胶为基的衬层残渣稳定性问题。
- But PF resin has got several defects either, such as high cost, long curing time, dark glueline color, easy to crack in glueline and so on. 但酚醛树脂胶也存在着成本高,固化时间长,胶层颜色深,胶层易龟裂等突出缺点。
- As the amount of curing agent and the curing temperature is raised,the curing time is shortened and the curing result is improved. 实验结果表明其固化时间均随固化剂用量的增加和固化温度的升高而缩短,且固化产物性能提高。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries