您要查找的是不是：
- crank shaft alignment measurement 曲轴对中测量
- crank shaft alignment 曲轴对中
- Has the shaft alignment been finished? 轴的对中任务完成了吗?
- Every bike has a serial number near the crank shaft. 每辆自行车在曲柄轴附近都有一个序列号。
- Aligning main engine's crank shaft and intermediate shaft after launching. 下水后主机曲轴和中间轴连接后校中。
- Bushings (4): Furnishes shaft support at three locations for positive shaft alignment and actuator support. 衬套（4）：在三个位置上配置轴支撑，有利于轴校直和执行机构的支撑。
- Measuring deflection of crank shaft of M.E. before starting up(after sea trial). 主机动车前（航行试验后）曲轴甩档测量。
- Technical requirement on propulsion shafting align. 内河船舶推进轴系校中技术要求。
- Bushings: Furnishes shaft support at three locations for positive shaft alignment and actuator support. 衬套:在三个位置上配置轴支撑,有利于轴校直和执行机构的支撑。
- Calculation and field test show that,by using this auxiliary balancing device, both the peak value and the fluctuation of the crank shaft to... 理论计算及现场试验结果表明，该平衡装置具有降低曲柄轴扭矩峰值、减少曲柄轴扭矩波动及降低抽油机耗电等优点。
- The characters of the electric drive of crank shaft press were studied from the viewpoint of the press working behavior. 从曲柄压力机的工作性质出发,分析了其电力拖动的特点以及电机功率的选择问题。
- The authors analyze the motion law of the balancing mechanism,the forces on the counterbalance and the torque on the gearreducer crank shaft. 还对平衡机构的运动规律、平衡块受力及减速箱曲柄轴扭矩等进行了分析。
- Then, `Retsina Shaft Alignment and vibration calculation software based on the Microsoft COM technology has been developed. 目前，国内关于船舶推进轴系校中和振动计算分析等理论研究和软件开发，还停滞在引进国外技术和软件的基础上，开展对推进轴系校中及振动理论和计算软件的研究与开发，具有较大的理论意义和重要的实用价值。
- The warp ends are drawn through heddle eyes in the correct manner and in the turning-over of the crank shaft of the loom, a shed is formed with each turn. 经纱以一定的方式被穿在综丝眼中，通过织机开口机构的驱动上下运动，形成梭口。
- Crank shaft,the severe material test will make it hardness and durance. a illtle bit vibration when circulation after balance spindles correction to prolong mechanical life. 曲轴经严格材料测试，坚固且耐用，平衡鎚经精密校正，运转时，震动小。
- The former causes forced vibration at the circular frequency of the crank shaft and the latter causes transient vibration at the natural frequency of the press. 惯性力激发的振动是以曲轴转速为频率的强迫振动，加工力激发的是以压机固有频率为频率的过渡振动。
- By the analysis of several gas forces in the twin-scroll compressor, the calculation formula of working volume and all different crank shaft angle are derived. 分析了双头涡旋齿涡旋盘所受的各种气体力，提出了在任意曲轴转角下的各种气体力及工作腔容积的计算公式。
- This article has engaged in physical and chemical experiments and analyses of outward appear-nace and microcosmic for nodular cast iron crank shaft of big powerful diesel engine. 对大功率柴油机球墨铸铁曲轴进行了宏观、微观全面的理化检验及分析;
- In this paper, ship shafting alignment was analyzed in detail by use of three-moment method. 针对某一具体船舶轴系,利用三弯矩法对其校中作了详细分析,给出轴系简化处理方法和实际参数。
