您要查找的是不是:
- Analysis of fatigue reliability of crank pin of beam pump unit. 游梁式抽油机曲柄销疲劳可靠性分析
- Examine carefully the crank pin for flaws or hair cracks. 精心检查曲柄销颈有无缺陷或微小裂纹。
- There is a pin hole between outside shell and output axis. 外套与输出轴的径向有一个插销孔。
- One such crack formed on the net section at the pin hole, much like an eyebar failure. 形成在销钉孔净截面处的一条裂纹非常象眼杆破坏。
- The beam and crank pin bearing adopt tip bearing structure to decrease the shaking due to the install difference and operation of pumping unit. 横梁轴承及曲柄销轴承采用调心轴承结构,以降低安装造成的误差和抽油机运转时的振动。
- The undersigned did deem that if the non-parallelism of the crank pin exceeds permissible limitation, crank pin and bearing were caused to be burnt. 下列署名的验船师认为曲柄肖不平行度超过允许值时会导致曲柄肖和轴承烧坏。
- The main causes is analysed for looseness of the threaded connection on pumping unit crank pin and the corresponding preventive measures are proposed. 分析抽油机曲柄销螺纹联接在使用中发生松动的主要原因,并提出相应的预防措施;
- Drilling method of pin hole: the pin hole shall be predrilled by supplier prior to hot dip galvanization. 销钉孔的钻法:销钉孔应为供应商在热镀锌预钻好。
- Flux Corrosion is typified by pin hole leaks, generally in the bottom of a horizontal line. 典型例子是由于针孔泄漏导致的焊剂侵蚀,通常发生在水平管道的底部。
- The procedures are chamfering both sides of the gudgeon pin and crank pin core and semi-finishing the crank pin bore at a rate of 1000 pieces per hour at 100% efficiency. 加工工序是对活塞销孔和曲轴销孔的两侧端面倒角,并半精镗曲轴销孔,在负荷率100%25时,生产率为每小时1000件。
- The paper analyses the necessity for piston in modern auto to adopt noncircular pin hole. 简述了采用活塞异形销孔的必要性及其结构特点。
- The Si-Mn steel track plate and pin usually exist the early abrasion, one of the main reasons is the burr defect of pin hole. 硅锰钢履带板销孔存在脉纹铸造缺陷是造成履带板与履带销出现早期磨损现象的根本原因之一。
- The Si-Mn steel track plate and pin usually exist the early abrasion,one of the main reasons is the burr defect of pin hole. 硅锰钢履带板销孔存在脉纹铸造缺陷是造成履带板与履带销出现早期磨损现象的根本原因之一。
- By homogenous design and Seger's glaze theory,a high-grade sanitary pocerlain glaze has been obtained,which possess a glossy and no pin hole surface. 利用均匀设计法和塞格尔釉式理论,研制出一种釉面光泽度高且无针孔的高档卫生陶瓷釉料。
- Of course after a while the novelty of it is gone - tame to take a rangefinder, a pin hole camera, or whatever I never did. 但是最终这意味着我不得不花费更多的时间和精力去拍我的相片。它强迫我在构图时以一种新鲜的视觉去看,去试验相机的摆放位置。
- High strength bolts for steel structure, bolts for diggers, hex bolts with split pin hole, bolts for automobile cylinder cap and non-standard components. 高强度钢结构螺栓,挖掘机螺栓,六角头绞制孔螺栓,汽车缸盖螺栓及非标准件。
- A new machining principle for non-cylinder pin hole of piston was presented by using giant magnetostrictive material (GMM) to control the deformation of tool rod. 摘要利用超磁致伸缩材料的特性控制刀杆弯曲变形,提出了一种加工活塞异形销孔的新方法。
- The NC boring lathe equipped with this kind of deformable arm can bore special shaped pin hole for piston efficiently, and meanwhile meet the demand of micro meter accuracy. 装有这种新型变形镗杆的NC镗床能高效地镗削活塞异形销孔,并达到微米精度的要求。
- crank case crank pin crank shaft crance 箍圈
- The Design of Crank Pin for Motorcycle Engine 摩托车发动机曲柄销设计初探