您要查找的是不是：
- Clockwise or counter clockwise rotation 顺时针或逆时针旋转
- counter clockwise rotation 反时针方向旋转,反时针旋转,反时针回转
- Turn the wrench counter clockwise direction. 请将刀头逆时针方向旋转。
- Clockwise rotation viewed from motor. 由电机向叶轮看顺时针旋转。
- The other potentiometers should be all rotated counter clockwise. 另一个电位计应该完全逆着顺时针方向旋转。
- Rotation direction: clockwise rotation viewed from motor end. 泵的旋转方向：由电动机方向往泵看为顺时针方向旋转.
- A clockwise rotation, around the origin and by the specified angle. 沿原点并按指定角度顺时针旋转。
- Place a wrench on the parallel flats of bonnet and stem assembly. Turn counter clockwise and remove. 将一把扳手放置在阀盖和阀杆总成的平行平面上。顺时针旋转并拆卸。
- The winding direction of a triangle indicates the direction in which the vertices are ordered. It can either be clockwise or counter clockwise. 转动的方向表示三角形顶点的排序方向。可以是顺时针也可以是逆时针。
- After finishing using, be sure to close the key switch firstly. Turn it counter clockwise to the vertical state. 首先关闭钥匙开关,逆时针旋转钥匙开关,使之处于垂直状态。
- Rotate the potentiometer P7 completely clockwise, P2 and P4 completely counter clockwise. 使有效的P7完全地顺时针旋转，P2和P4完全地相反地顺时针。
- To use the Timing Bezel:Rotate the bezel counter clockwise until the O on the bezel lines up with the minute hand. 使用表面计时表圈（时间读取装置）：逆时针旋动表圈，直到表圈上的O标记对准分针。
- Applies a clockwise rotation of the specified angle to the local geometric transform. 将指定角度的顺时针旋转应用到局部几何变换。
- Key left for the counterclockwise direction of rotation, and the right direction for the key clockwise rotation. 左方向键为逆时针转动,右方向键为顺时针转动。
- Close the regulator. After relieving all the gas pressure, turn the adjusting knob counter clockwise as far as it will go. 关闭调整器。在释放了所有的气体压力之后，逆时针旋死控制钮。
- Positive frequencies are produced by anticlockwise rotation and negative frequencies by clockwise rotation. 正频率是用逆时针旋转来产生，而负频率是用顺时针旋转来产生。
- When in a situation where you have to pass food or condiments to others at the table, pass it to your right, or counter clockwise. 当你必须传递食物或调味品给餐桌上其它人的时候，记得从右边传，或者说按逆时针方向传。
- This connection has a left-hand thread (loosens with clockwise rotation) and requires a gasket to seal. 这种接头具有左手螺纹（顺时针旋转为松开），要求使用垫圈来密封。
- In response to indentation of the Pamir wedge and tectonic movements along the Altyn Tagh fault, the Tarim basin underwent clockwise rotation about a vertical axis since the Tertiary. 区域构造研究表明，塔里木盆地新生代主要发生了4期区域构造变形，第三纪以来还发生顺时针旋转。
