您要查找的是不是:
- clamping force calculation 夹紧力计算
- Clamping force equalization: same force to two workpieces in different size. 自动补偿机构:不同大小工件,可在同时夹紧,且夹持力相同。
- But the Grand Tech-UBE injection moulding machine can make it due to its design of precise mould clamping force detecting sensor as well as the reception and calculation system of the computer. 但 Grand Tech-UBE 注塑机却能如此,因其具有精确设计的锁紧力探测接收感应器和电脑接收与计算系统。
- Size and grade specific cap bolts offer superior clamping force between the cap and base. 座罩螺栓有不同的尺寸和等级,在座罩和基础之间形成理想的夹持力。
- In using an injection moulding machine, it is best to use the minimal but adequate clamping force F. 使用注射成型机,最好使用最小同时充足的锁模力F。
- The two deices do clamping force measurement/control and caity pressure switchoer to holding pressure. 这两个装置就是锁紧力量测/控制装置和(射出)转保压的模腔压力转化装置。
- Choosing a PIMM simply on the basis of shot weight is too simplistic.Neither is clamping force alone sufficient. 仅仅基于射出重量去选择注塑机是不够的,同样的,仅考虑锁模力也不可以。
- Furthermore, a high clamping force compresses the toggles and the mould, and stretches the tiebars, reducing the fatigue lives of the toggle pins, the mould and the tiebars. 高锁模力对曲轴结构和模具产生挤压,对拉杆(控制开合模甚至锁模的四个大杆)产生拉伸,从而降低他们的疲劳寿命。
- An excessive clamping force distorts the mould and the mould cavity unnecessarily, affecting the precision of the moulded part. 过大的锁模力会使模具以及模腔产生不必要的变形,影响成型品的精度。
- This paper focus on simulating the KM toolholder taper interface positioning under different clamping force by using Finite-element Method. 针对KM刀柄锥面定位在不同夹紧力下进行有限元模拟,得到径向位移、接触应力、锥面间隙结果。
- The internal force calculation, bearing capacity of bridge abutments, eccentricity, stability against overturning and sliding were carried out during the study. 内力计算,桥台台身底和基底承载能力验算、偏心距验算、桥台基础抗倾覆与抗滑动稳定性验算。
- Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究结果表明:采用微孔发泡注射成型工艺可以节省原材料10%25;注射压力降低了36.;7%25;锁模力降低了60
- Twoprocess mode can be ed, single or continuous. The clamping force of hold down device will in crease when cutting force increases. 两种使用模式给客户选购,单次或连续。另压片力会随着剪切力增加而自动调节。
- Its paper clamp presses tightly against the material to be cut by means of a high quality strong pull spring assembly and the clamping force can be adjusted readily. 压纸器是由优质强力拉簧组使其牢牢地压紧裁切物,压力大小调整方便。
- Deciding the overall concept of jigs, which include the method of machining, method of fixing and analysis of fixing error, method of clamping and the calculation of the clamping forces of cutting . 确定夹具总体方案,包括加工的方法、定位方案和定位误差的分析、夹紧方案、切削夹紧力的计算。
- The mechanics models of metal-bands transmission concerning clamp force of pulley, axial force, thrust and tension is built based on Coulomb friction theory. 以库仑摩擦理论为基础,在考虑了带轮夹紧力、轴向力、挤推力和金属环张力的基础上,建立了金属带传动的力学模型。
- From Rayleigh Ritz method of energy theorem, this paper puts forward the critical force calculation method considering the dead weight of the pier, which can also be applied to variable sectional area piers. 从能量原理的瑞利-里兹法出发,提出了考虑墩身自重,并能运用于变截面墩的临界力计算方法。
- The alterable clamping force fixture can automatically adjust its clamping force to adapt to the cutting force to reduce the cutting deformation of machining system. 变夹紧力夹具能够适应切削力的变化,自动调整夹紧力的大小,以减少加工系统的切削变形。
- To control material's flow more better and improve the accuracy of numerical simulation, drawbead mechanics principle is introduced and drawbead restraining force calculation method is studied. 为更好地控制材料的流动,提高数值模拟的精度,研究了拉延筋 的力学机理,在此基础上研究了拉延筋约束阻力的计算方法。
- Insufficient clamping force gies rise to flash at the mould joint.Most PIMMs today use their clamping force (in tonnes) in their model name, e.g.ME125III. 锁模力不足会引起模具结合处的飞边,现在大多数注塑机都采用其锁模力(单位:吨)作为其型号名称,如:ME125III。