您要查找的是不是：
- Research results show that with application of Mucell,the 10% raw material can be saved,the injection pressure is decreased by 36.7%,the clamp forc... 研究结果表明:采用微孔发泡注射成型工艺可以节省原材料10%25;注射压力降低了36.;7%25;锁模力降低了60
- The mechanics models of metal-bands transmission concerning clamp force of pulley, axial force, thrust and tension is built based on Coulomb friction theory. 以库仑摩擦理论为基础，在考虑了带轮夹紧力、轴向力、挤推力和金属环张力的基础上，建立了金属带传动的力学模型。
- Modern presses make it easy to adjust clamp force, even on toggle presses, so there is no excuse for overdosing on clamp. 过量或超出必要的锁模力设定，同时也是对能源的一种浪费，不管是液压机，机械式的，电动的。
- Molder's rule of thumb for maximum clamp force is usually 3.5 tons per square inch of projected part area, for most wall thicknesses and for most resins. 通常对于不同模厚的模具，以及大多数的原材料，最大的合模力设定在3.;5吨/每平方英寸。
- This paper anlayses and strudies effect of cutting force,clamp force, rotational inerta,gravity on working accuracy of thin_wall long cylindric part machined with double_tool. 分析和研究了双刀切削加工薄壁长筒类零件时,切削力、夹紧力、惯性力、重力对加工精度的影响。
- Years ago, in a monthly article, that my mentor Bill Tobin wrote for a monthly magazine, he touched on the importance of clamp force and the mistakes many Molders make by using too much clamp tonnage. 几年前，在一份月刊的文章里，我的导师BillTobin为一份杂志写了一篇文章，是关于锁模力的重要性，里面谈到了许多注塑员在日常工作中，经常会使用过大的锁模力。
- Clamping force equalization: same force to two workpieces in different size. 自动补偿机构：不同大小工件，可在同时夹紧，且夹持力相同。
- Its paper clamp presses tightly against the material to be cut by means of a high quality strong pull spring assembly and the clamping force can be adjusted readily. 压纸器是由优质强力拉簧组使其牢牢地压紧裁切物,压力大小调整方便。
- The wood is held in position by a clamp. 木头用钳夹固定住了。
- Size and grade specific cap bolts offer superior clamping force between the cap and base. 座罩螺栓有不同的尺寸和等级,在座罩和基础之间形成理想的夹持力。
- The clamps should be stable, the clamping force should be in normal direction to the support surface. 5夹紧器要稳定可靠，夹紧方向按定位面法线方向。
- In using an injection moulding machine, it is best to use the minimal but adequate clamping force F. 使用注射成型机，最好使用最小同时充足的锁模力F。
- The two deices do clamping force measurement/control and caity pressure switchoer to holding pressure. 这两个装置就是锁紧力量测/控制装置和（射出）转保压的模腔压力转化装置。
- Choosing a PIMM simply on the basis of shot weight is too simplistic.Neither is clamping force alone sufficient. 仅仅基于射出重量去选择注塑机是不够的，同样的，仅考虑锁模力也不可以。
- Clamp these two pieces of wood together. 把两根木头钳紧。
- Furthermore, a high clamping force compresses the toggles and the mould, and stretches the tiebars, reducing the fatigue lives of the toggle pins, the mould and the tiebars. 高锁模力对曲轴结构和模具产生挤压，对拉杆（控制开合模甚至锁模的四个大杆）产生拉伸，从而降低他们的疲劳寿命。
- An excessive clamping force distorts the mould and the mould cavity unnecessarily, affecting the precision of the moulded part. 过大的锁模力会使模具以及模腔产生不必要的变形，影响成型品的精度。
- This paper focus on simulating the KM toolholder taper interface positioning under different clamping force by using Finite-element Method. 针对KM刀柄锥面定位在不同夹紧力下进行有限元模拟,得到径向位移、接触应力、锥面间隙结果。
- Twoprocess mode can be ed, single or continuous. The clamping force of hold down device will in crease when cutting force increases. 两种使用模式给客户选购，单次或连续。另压片力会随着剪切力增加而自动调节。
- It is vain to attempt to root out heresy by force. 试图用暴力消除异端邪说是徒劳的。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
