您要查找的是不是：
- casing test pressure 泵壳试验压力
- All models are certified at 300 PSI test pressure and 150 PSI working pressure. 所有型号都通过300PSI试验压力检验和150PSI工作压力检验。
- All Oil-Powered water heaters are certified at 300 PSI test pressure and 150 PSI working pressure. 所有燃油热水器都通过300psi(2068kPa)实验压力和150psi(1034kPa)工作压力检测。
- This test pressure includes corrections for service conditions e.g. backpressure or high temperatures. 此试验压力包括工作条件如：背压和高温的校正值。
- According to the test pressure and nominal pressure of pipes,calculated and compared their numerical value. 结合管材测试压力和公称压力,计算并比较了它们之间的数值。
- Besides use notebook computer, there is a kind of a few yuan special tester on market, signal can give in the case test that does not need to dial expedite. 除了使用笔记本电脑外，市面上有一种几十元的专用测试器，可以在不需要拨号的情况测试出信号是否畅通。
- The TK-DL can test pressure vacuum breakers, reduced pressure backflow preventers or double check valve assemblies. TK-DL可以检测压力真空断路阀，减压防回流阀或双止回阀总成。
- Kang Hongwen, Wang P. and Xu X., ” Study on application of adaptive grids technique in numerical model，Part II: Two-dimensional case test”, Chinese J. A. S., in press. 康红文，王鹏云和徐祥德,“自适应网格技术中权函数问题的研究”,西部大开发：气象科技与可持续发展学术研讨会,23-29,2000
- Cold differential test pressure the pressure at which a valve is set on a test rig using a test fluid at ambient temperature. 冷差试验压力（或冷态差分试验压力）：在此压力下，阀门固定在试验台上，用一试验流体于室温下作试验。
- Pressurisation should be suspended at intervals on the way up to the test pressure to allow time for inspection to find leaks. 在达到测试压力之前的增压过程中应有间歇暂停时间，以便进行检查，以发现有无泄漏。
- Hose corrugation deformation will occur if the maximum rated working pressure is multiplied by 150% to determine the maximum rated test pressure. 波纹软管变形会出现，如果最大额定工作压力乘以150 %25 ，以确定试验压力最大额定。
- Our precision test gauges with mirrored scale are manufactured with highest precision and are used to test pressure in research and development and in laboratories. 我们的高精度校验表是根据最高标准生产的,用于研究和开发部门以及实验室的压力校验。
- In experimental measurement, F P laser interferometry and auto measurement system are used to take F P interference pictures and test pressure distributions. 实验测试应用F－P激光干涉仪和自动测压系统，得到流场F－P干涉照片和压强分布。
- Normal service relief valves, expansion bellows and any other fittings not designed for the full test pressure, must be removed or positively isolated from the system. 必须将正常操作卸压阀、膨胀波纹管和任何其它未经设计用于满压测试的管件拆除或与测试系统完全隔离开。
- In that case you'll have to clear yourself. 那样，你只得自行辩白了。
- The test pressure shall be within the limits set forth by the Hydraulic Institute. Certified copies of the test results shall be submitted to the design engineer upon request. 测试压力应该在美国水利协会规定的范围内。如果需要的话,测试结果的批准文件应该提交给设计工程师。
- In this case, let's start earlier. 既然这样，我们就早点开始。
- Complicated phas variation and phase state redistribution exist in condensate gas wells.This may result in considerable effect on derivative curves of well test pressure. 凝析气井存在复杂的相变与相态重新分布，对试井压导曲线有较大影响，正确选定分析直线段是解释成败的关键。
- If it is elected to hydrostatically test such lines, the minimum test pressure shall conform to section 3.1.1 herein and supports shall be designed accordingly. 如果这些管线要进行液压试验，则最低试验压力应符合本技术条件第3.;1
- Relief valves set for the test pressure should be installed if necessary to give protection to the system against the risks of overpressure during the test. 必要时应安装测试压力的卸压阀装置以保护系统在测试过程中抵御超压危险。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
