您要查找的是不是：
- notch break test for butt welded joint 对接接头缺口断裂试验
- guided-bend test for butt welded joint 对接接头靠模弯曲试验
- steel butt weld joints 钢制对接焊接接头
- butt weld joints 对接焊接接头
- butt weld joint 对焊接头
- Basic Fatigue Curves of Butt Welded Joints in Two Kinds of Structural Steel Plate 两种结构钢板焊接头的基础疲劳曲线
- The distribution of residual stress of weld joints is analyzed. 并分析了焊接接头残余应力的分布规律。
- Some crack extension probably developed from the unfused section of the butt weld across the thickness of the stiffener during transport and erection. 有些裂纹可能在运输和安装过程中就从加劲肋对接焊未熔透处开始发展。
- Seals underbody, weld joints, trunk interior and firewall of motor vehicles. 汽车底盘，焊缝，卡车内饰等。
- This indicated that the fracture had initiated at the unfused butt weld in the longitudinal stiffener. 研究表明裂纹是从纵向加劲助未熔透的对接焊缝中起始的。
- Body ? streamlined flow path minimizes pressure drop. Butt weld, venturi or flanged ends provide piping alternatives. 阀体?流线形流道，最大限度减少压降。对焊、缩喉管或法兰连接端口几种可供选择的连接方式。
- Turbulence, erosion and pressure drop are minimized.Flanged End-Crane cast steel gate valves are available in flanged end and butt weld ends. 所有阀盖构件都是铸件，并且按照严格的一致的公差标准进行抛光，使得阀体与阀杆能够准确校准，密封更加容易。
- Body: Strong construction assures maximum safety over the recommended pressure and temperature range. Both flange and butt weld ends are available. 阀体：坚固耐用的结构，确保在相应的压力温度等级范围内的安全性。可提供法兰和对焊两种连接方式。
- This paper describes the difference between the terms of groove and bevel in weld joints and condition in ASME Code translation. 本文叙述焊接接头中术语剖口与坡口的区别和在ASME规范翻译中应注意的问题。
- The butt weld is easier to inspect nondestructively than the fillet welds. 对接焊缝比角接焊缝更容易进行无破坏检查。
- This article introduced the experiment of residual stress in flat tubeplate head of large scale fuel boiler that was manufactured by cold rotary extruding and butt weld. 本文介绍了大型燃油锅炉经拼板焊接和冷旋压加工制造而成的平管板封头残余应力试验。
- Fig.6 The effect of heat input on the UTS of the TIG welded joints. 图6线能量与钨极氩弧焊焊接接头极限抗拉强度的关系。
- Butt welded joint 对接焊接头
- Where filler materials having tensile properties deviating (downwards) from the parent metal are used, this fact must be taken into account when dimensioning the weld joints. 从母材部分开始使用具有伸缩性的填角材料之处，计算焊缝时应该考虑到这种情况。
- Fractured 1Cr18Ni9Ti butt welding flange was analysed by OM, SEM and EDX. 用光学显微镜、扫描电镜和能谱仪分析了 1 Cr1 8Ni9Ti对接焊法兰盘断裂原因。
