您要查找的是不是：
- The side or surface that is underneath; the bottom side. 下面; 底面在下的面或表面; 底面
- Mark of "HR" is stamped on its bottom side. 地板侧面有钢印标志“HR”。
- He turned the box over to examine the bottom side. 他把那个盒子翻过来对底面进行检查。
- The side or surface that is underneath;the bottom side. 下面；底面在下的面或表面；底面
- A three-dimensional border on the bottom side of the rectangle. 该矩形底边的三维边框。
- Figure 3. Bottom side of a plastic stencil, showing undercut features to sit over board components. 塑胶底侧，有砍口，可以盖在电路板元件上。
- Its bottom side also has supporting points and its northeastern end is connecting with the hill massif. 如果将三块碑材叠将起来，总高度可达78米，总重量为31167吨，堪称绝世碑材。
- If the side bearing gap is too big, it will not restrain efficiently the roiling of car-body when roll restoring moment is not sufficient. 而过大的旁承间隙又使旁承在侧滚回复力矩不足时不能有效抑制车体的侧滚。
- Comparative experiments were conducted to investigate the metallurgical, effects of top, bottom side and bottom argon blowing techniques. 为考察顶吹氩、侧吹氩及底吹氩的冶金效果，分别进行了三种吹氩工艺的对比试验。
- Remove differential side bearings from differential case. 从差速箱拆卸差速器侧轴承。
- Low solids flux for surface mount assemblies designed to help reduce skips on bottom side surface mount pads. 用于表面安装组件的低固态物焊剂,有助于减少表面安装焊盘底侧的遗漏现象。
- Body: Hardcoat Anodized, precision machined mounting surface with tapped hole accessible from bottom side. 身体：硬膜阳极氧化，精密加工与螺纹孔安装从底部可接近表面。
- If a cover design-time to set aside the bottom side of the head, burrs, and sizes, this behavior completely avoidable. 如果在封面设计时留出天头，地脚的毛边尺寸，这种现象完全可以避免的。
- Set in the adhesive viscoelasto, used in the production process is how you will cause a large head, the bottom side of the hemomediastinum. 而在无线胶黏订生产工艺中，采用上述操作，就会产生很大的天头、地脚破口。
- Two trapezoids are the same in shape and hold a common winding as the bottom side, while the midpoint of the common winding is the ground of four phase systems. 2个梯形形状相同，并具有共同的底边，其中点为四相系统的公共点。
- Bogie side bearing sliding block 下旁承滑块
- Then according to the bearing behavior of arcade tunnel,the internal force of one side bearing and both sides bearing have been calculated and analyzed by using the method of loading-structure. 接着根据连拱隧道的承载特点,按荷载结构法分析计算了单侧承载及整体承载条件下的隧道内力,据此提出了一种简化为单拱的计算方法。
- The simulation results show that the filmworks as a collimating layer when the light incident from bottom side of cone and as ascattering layer while the light incident from tip side. 模拟计算结果表明，当光从微锥的底部人射时，该膜起到准直作用，当光从微锥的顶部入射时，该膜起到散射作用。
- The problems existing in reform of the upper side bearings assembly on present freight cars and the causes are analyzed. 分析了既有货车提速改造上旁承组装存在的问题及原因,并提出了相应的解决措施。
- The SY113 Move Roller Card Case, the bottom side is white color and attached (OR you can choose none attached) one international time circle. There is biggish area for advertisement on SY113 surface. SY113滚动滑片式名片盒,底板为白色，附有或者不附国际时差盘，超大面积广告位。
