您要查找的是不是：
- Specifications for particular types of winding wires - Part 35: solderable polyurethane enamelled round copper wire, class 155, with a bonding layer. 特种绕组线规范。第35部分:155级带粘结层的可焊接聚氨酯漆包圆铜线。
- In addition,The general macrograph characters of spalling of bonding layer and shallow working lining,and their causes were described. 总结了轧辊磨损预报模型的研究现状,并详细介绍了典型的磨损预报模型,最后展望了冷轧辊研究工作的方向。
- Pinealocyte, metalto tiscosity printing to a larger formation bonding layer of ink, and then set the printed matter move to dry heat source. 一栽是，首先不兵印品着上黏度较不小的油不朱变不败黏结层，然后不兵印品移至热源烘潮。
- A thermal barrier coating (TBC) consisting of CoNiCrAlY bonding layer and ZrO_2+Y_2O_3 surface layer was formed on the TiAl alloy surface by plasma spraying. 采用等离子喷涂方法在TiAl合金表面喷涂 ,得到由CoNiCrAlY粘结层和 (ZrO2 +Y2 O3)陶瓷外层组成的双层结构的热障涂层。
- But the welded joints can be pullled, bent and cold rolled without cracks formed on the bonding layer, so as the molten regions are small and distributed as isolated islands. 只要细小的熔化区孤立间断地分布在结合面上,焊接的接头能被拉伸、弯曲和冷轧,在结合层中无裂纹形成。
- The distributed force model of intelligent beam structures is presented in considering the effect of bonding layer on basis of hypothesis of linear strain in the paper. 基于线性应变假设，提出了考虑粘贴层影响的智能结构梁分布力模型。
- The influence of the bonding layer thickness and material properties, piezoelectric layer thickness, placements and feed-back control parameters on the vibration suppression are investigated. 分析了粘弹层、压电层厚度和压电片位置等结构参数变化以及材料参数变化对控制效果及结构频率的影响。
- It is shown that the effects of the stiffness and inertia of the piezoelectric element that lead to higher first natural frequency on the natural frequencies of the beam are significant, and that of the elastic modulus of the bonding layer is small. 研究表明，压电元件的刚度和惯量对梁的频率影响很大，变截面智能压电梁的一阶固有频率总是高于等截面梁的固有频率。
- By way of the tests, it is found that the process of laser remelting can increase the adhesive strength of cladding unless the process, such as energe density, bonding layer etc, is proper. 通过结合强度测试，发现只有在适当的工艺条件下，才能在激光重熔后得到结合强度较高的熔覆硬质合金层。
- The rubber to metal bonding mostly adopt sulphurate bonding.But if under sulphurating condition the bonding layer is unstable, or suppurating craft is difficult to come true，we adopt cold bonding. 橡胶与金属粘合大都采用硫化粘合方式,但当硫化条件下基材不稳定或硫化粘合工艺不易实现时则采用冷粘方式。
- The bond layer has no holes, and the edge bond rate amounts to above 98%, and the bond strength is above 220 kg/cm 2. By doping the same kind dopant with low resistance, realizes the stress compensation. 实现了键合层无孔洞， 边沿键合率达98%25 以上， 键合强度达2156 Pa 以上， 并通过在锗中掺入与低阻同型号的杂质， 实现了应力补偿。
- You need a strong adhesive to bond wood to metal. 需要强力胶才能把木料粘在金属上。
- This glue makes a good firm bond. 这种胶水粘得很结实。
- Common tastes form a bond between the two men. 共同的爱好使两人结交为朋友。
- This layer of rock contains a lot of flint. 这一岩层中有大量燧石。
- The bond that binds the smugglers together is a rope of sand. 把走私犯联接起来的是条沙做的绳子，一碰就碎。
- The inner layer of the wall of a spore. 孢子内壁孢子壁的内层
- Common interests formed a bond between us. 共同的利益把我们联系在一起。
- Identity of interests is the bond that unites them. 利害的一致是把他们联合起来的纽带。
- There is a fine layer of dust on the desk. 桌子上有一层薄薄的尘土。
