您要查找的是不是：
- incremental-step blind hole drilling method 逐层盲孔钻削法
- The hole drilling method is presented to measure residual stresses in orthotropic materials. 讨论了小孔法测量正交各向异性材料残余应力。
- Strain gage hole drilling method is one of the most popular residual stress measurement methods. 应变片钻孔法是工程中应用最广的残余应力测量方法之一。
- The relieved coefficients during the measurement of the residual stresses in the fiber reinforced composites by the hole drilling method were given with conversion of the two coordinate systems. 针对纤维增强复合材料的属性特点,应用坐标系转换原理推导出通孔法测量复合材料残余应力时的应力释放系数公式。
- Residual Stress Test of Automotive Brake Drum Using the Hole Drilling Method 钻孔法测取汽车制动鼓的残余应力
- STEP HOLE DRILLING METHOD FOR MEASURING PLANE RESIDUAL STRESSES IN DEEP LAYER 钻阶梯形孔法测量深层平面残余应力
- Relieved Coefficients during the Measurement of Residual Stresses in the Fiber Reinforced Composites by the Hole Drilling Method 小孔释放法测纤维增强复合材料残余应力的释放系数
- WISDOM DEEP HOLE DRILLING MACHINE CO., LTD. 慧能深孔机械有限公司。
- Dual action: hammer drilling and hole drilling. 二模式动作:锤钻及单钻孔。
- DEEP HOLE DRILLING TECHNOLOGY LTD. 北京哈镘深孔技术有限公司。
- If hollow concrete block, brick blind hole marked slabs, not sintering. 如空心水泥砌块、盲孔砖、标砖等,不用烧结。
- hole drilling method 小孔释放法
- The uncertain factors in the welding residual stresses measurement by blind hole technique are analyzed with the fuzzy mathematic method to evaluated the strain release factor A and B. 摘要在分析一些引起盲孔法检测焊接残余应力测量误差的不确定因素的基础上，引入模糊数学方法对应变释放系数进行评价。
- Drilling method of pin hole: the pin hole shall be predrilled by supplier prior to hot dip galvanization. 销钉孔的钻法：销钉孔应为供应商在热镀锌预钻好。
- Replace length cut springs to std. springs. Close blind holes. 将定尺弹簧改成标准弹簧.;关闭盲孔
- The rotation graphic method for calculating the regulating angle in the machining of the hole drilling is presened. 提出采用旋转图解法计算钻孔加工中的调整角度。
- Now this technique is applied in the slim hole drilling in Daqing Oil Field. 目前，此项技术已在大庆油田小井眼钻井中推广应用。
- In level hole drilling,by the using of numerical valule analysis method,the mathematics model of drill hole depth and dip angle relation under someone stratum is set up. 在水平孔钻进中,利用数值分析方法,建立在某种地层下按某种钻具组合和钻进参数钻进时,孔深和倾角关系的数学模型。
- This drilling method is simple operated and quite fit for worksite operation. 该方法操作简单,非常适合于现场操作。
- The new method for machining keyway in holes and the special tool is presented, with which the keyway not only in blind holes but also in shoulder holes can be machined. 介绍了一种加工孔内键槽的新方法和相应的专用工具。不但可用来加工通孔内的键槽，而且还能用来加工盲孔内的键槽或有障碍台肩的孔内键槽等。
