您要查找的是不是：
- Open bleed valve "A" on top of test kit and bleed air from hose. 开启检测组件顶部的排气阀“A”，并且从软管排放空气。
- bleed air valve 泄气阀
- Open vent needle valve and bleed air from hose. Then close vent valve. 开启排气针形阀，并从软管排放空气。然后关闭排气阀。
- ENGINE BLEED AIR CONTROL SYSTEM. 发动机引气控制系统。
- Bleed air from kit by opening TC #4 to establish flow through the backflow preventer and prevent premature opening of the relief valve. 通过开启测试旋塞4号从组件上排放空气，引导通过防回流阀的流体，防止安全阀过早开启。
- Attach hoses as shown. Bleed air from kit, close No. 2 shutoff. 如图所示接上软管。从组件上排放空气，关闭2号关闭阀。
- C. Attach hoses as shown. Bleed air from kit, close No. 2 shutoff. 按照图示连接软管。从组件上排放空气，关闭2号关闭阀。
- Open test cock then open needle valve "A" and vent or bypass needle valve. Bleed air from hose then close vent needle valve. 开启测试旋塞，然后关闭针形阀“A”、排气口或旁路针型阀。从软管中排气，然后关闭排气针形阀。
- Smooth operation of throttle linkage and throttle body air valve. 节流连杆和节流体空气阀的平稳操作。
- Unthread the pump from the air valve and measure sag. 参考气压设定建议数值表打入相应气压以达到所需的预压行程。
- Open vent needle valve and needle valve "A" to bleed air. Close needle valve "A". Open needle valve "B" to bleed air and then close "B" and vent needle valve. 开启排气针形阀和针形阀“A”，排放空气。关闭针形阀“A”。开启针形阀“B”排放空气，然后关闭“B”和排气针形阀。
- Equipped with air valve to ejecting the products by blowing. 配备吹气装置以便于脱模。
- Repeat steps2-5 until proper sag is achieved, then replace the air valve cap. 重复2－步骤以达到最佳预压行程后，盖上气阀嘴帽。
- Repeat steps 2-5 until proper sag is achieved, then replace the air valve cap. 重复2－5步骤以达到最佳预压行程后，盖上气阀嘴帽。
- Locate the Schrader air valve on the shock and remove the air valve cap. 找到避震上的美嘴气阀，取下气阀帽。
- Install bypass hose between VA and VB. Open VB and bleed air by loosening hose connection at VA. Tighten hose connection and close VB. 在VA和VB之间安装旁路软管。开启VB，松开连接在VA上的软管连接排放空气。紧固软管连接，并关闭VB。
- Install bypass hose between VA and TC #4. Open VA, then bleed air by loosening hose connection at TC #4. Tighten hose connection. Close VA. 在VA和测试旋塞4号之间安装旁路软管。开启VA，然后松开连接在测试旋塞4号上的软管排放空气。紧固软管连接。关闭VA。
- Due lack parts，for troubleshooting，interchanged bleed air regulator of R engine with L engine，running-up test normal. 由于航材缺件，为判断故障，左右发对串引气调节器，试车检查右发引气压力正常。
- An overall air control for each pipe in each room is available by fitting an air valve at the hot water supply. 把空气阀安装在温水供给器时可综合处理各房间管路内的空气。
- Open vent needle valve and bleed air by opening needle valve "A". Close "A" then open needle valve "B" bleeding air and then closing "B". 开启排气针形阀并通过开启针形阀“A”排放空气。关闭“A”，然后开启针形阀“B”排放空气，然后关闭“B”。
