您要查找的是不是：
- Use ice do massage the back of hand between thumb and index finger(V shape). 在手背的拇指和食指中間的V字形的部分，用冰塊來摩擦。
- From the inside corner to extend the line Yanshao, and Erjian a V shape. 從內眼角至眼梢的延長線，與耳尖構成V字形。
- The most optimistic outlook would be a 」V」 shaped recovery in which growth plunges and then rebounds quickly. 最樂觀的看法是呈V型復甦，即成長遽降，然後快速反彈。
- A large deformation elastic plastic FEM model is employed to simulate the stretch flanging of V shaped sheet metal parts. 採用彈塑性大變形有限元方法研究了幾何形狀和材料參數對「V」型零件翻邊的影響;
- The method of using two right-and-left finial pedestal and one V shape pedestal was the best. 採用左右2頂尖座,再配一V形座附件是較好的一種方法。
- Lianxing was sharp and the V shape, the tone was a sharp sudden acute angle, formed from Wenduan to Erjian V shape. 臉形尖而呈V字形,口吻尖突呈銳角,從吻端至耳尖形成V字形。
- Complications rates of unstable trochanteric fractures treated with V shape nail and DHS were 27.2% and 19.4%, respectively. 不穩定型骨折中 ;V形釘組併發症為 2 7.;2%25;DHS組為 19
- Tracking experiment of MIG on V shape welding groove is made with this method,and the experiment result validates the validity of this method. 利用該方法對V形坡口進行了金屬熔化極氣體保護電弧焊(MIG)的跟蹤試驗,試驗結果驗證了所用方法的有效性。
- The machine through mechanical transmission, the machine makes material in two asymmetry V shape cylinders to turn over to-and-fro. The purpose of uniform can be got. 該機通過機械傳動，使兩個不對稱的V型圓柱體內的物料做往複翻動，達到均勻混合之目的。
- Flat bed machines that are used to make ribbed knit fabrics having two sets of needles arranged to form a V shape with the open end of the V parallel to the base of the machine. 生產羅紋織物的橫機有兩組針,呈v型排列,v型的開口與橫機的底座平行。
- Methods : to treat stenosing tenovaginitis with 「V」shape acupotome combined with manipulation, and treat the disease with block therapy as contrast group at the same time. 方法：針刀組採用「V」形針刀對腱鞘狹窄處推切，術后結合手法充分松解腱鞘；同時與局部封閉療法組進行了臨床對照；
- This machine is a kind of gray board V shaped slotter of the latest generation which overcomes the disadvantage that the corner folding of gift box is not good-looking when making gray board gift box. 本機針對灰紙板製作禮盒折角不美觀等缺點開發出來的最新一代灰紙板V槽設備.
- The centre of joint is characterized by fine equiaxial grains.The flashing is by lamellar structure.A「V」shape weld zone is formed from the centre of joint to the flashing. 心部為細小的等軸組織，焊口為片狀組織，從心部到焊口形成了V字形焊縫。
- He wants to widen his knowledge of the industry. 他想擴充自己在這一行業的知識。
- The road gradually widened until we found ourselves in a large valley. 路漸漸寬了起來，最後我們走進了一個大的山谷。
- The gap between the rich and the poor has widened. 貧富之間的差距擴大了。
- Before bending to V shape, the metal sheet should be slotted with V_shape of a certain depth on the bending line, then the metal sheet is bent to the required shape along the V_slot. 形彎曲成形前,對金屬薄板折彎處進行一定深度的V形開槽,然後在V形開槽處進行彎製成形,此種加工方法稱之為V形開槽彎曲成形技術。
- To produce CJ 3.6 tex in spinning frame with pneumatic V shape draft and guarantee yarn quality,processing of weight per 5 m,draft multiple of back area,roller gauge,top roller pressure,leading distance of front top roller an so on were optimized. 為了在氣動V形牽伸細紗機上順利生產CJ 3.;6 tex紗;保證成紗質量;對粗紗定量、後區牽伸倍數、羅拉隔距、膠輥加壓及前膠輥前衝量等工藝參數進行了優化試驗。
- When a pterosaur walked or remained stationary, the fourth finger, and with it the wing, could only turn upward in an extended inverted V shape along each side of the animal』s body. 而當它行走或不動時，第四指，連同翅膀，只能向上伸展，在身體兩側呈倒轉的V字型。
- To study growth and remove of concave, U and V shape crack defect using the method simulating transversal crack with test and FEM analysis in the course of multi-pass drawing stainless steel wire rod. 在多道次拉拔不鏽鋼線材過程中,用模擬表面橫裂的方法,通過試驗和FEM分析,研究凹形、U形、V形裂紋缺陷的生長和消除。
