您要查找的是不是:
- The Effect of SRM's Mass on the Thrust Measurement with a Vertical Test Fixture 立式試車時固體發動機質量對推力測量的影響
- Design and Analysis of Dynamic Characteristics of Vertical Test Fixture for Short-time and High-Thrust Motor 短時大推力發動機立式試車架動態特性設計與分析
- To design, fabricate and repair test fixture. 設計;製作和修理測試機架.
- To plan and control the assumption of test fixture materials. 計劃和控制測試機架原材料。
- The requirement for a good test fixture is maximum stiffness for the lightest possible weight. 一台好的試驗固緊裝置應該是重量輕而剛度大。
- Have rich experience on test fixture building, able to build pneumatic controlled fixture is prefer. 具有豐富的測試治具製作經驗,懂氣動控制治具製作優先。
- To prevent transients, always turn the source off while switching contacts in and out of the test fixture. 為了避免發生瞬變現象,一定要先將電流源關閉,然後再把接點接入測試夾具或將其斷開。
- DUT is placed in test fixture such a diode, transistors, microstrip circuit and so on. 被測件放在測試夾具里,如二極體、晶體管、微帶電路等。
- Figure 2-12 shows a high mega-ohm resistor (RDUT) supported on two insulators mounted in a metal test fixture. 圖2-12示出了測試夾具上由兩個絕緣子支撐的高阻器(RDUT)。
- Again, it may be more economical to cut the cables in half, then permanently connect the cut ends to the test fixture. 同樣,若將電纜分為兩部分,然後將被截斷的一端永久性地連接到測試夾具,則更經濟。
- The first step to verify the system requires that resistors of known value be placed in the test fixture. 驗證系統的第一步需要將一個已知阻值的電阻器置於測試夾具中。
- If mass-terminated cables are used, mating receptacles can be mounted at the test fixture. 如果採用接線頭電纜,在夾具上則可以安裝匹配插座。
- Use high-reliability, fail-safe interlock switches to disconnect power sources when a test fixture cover is opened. 採用高可靠性、自動防止故障的聯鎖開關,在夾具外罩被打開時能夠自動斷開電源。
- This paper introduces the test effects of the roadway support with yieldable legs including different construction on Vertical test stand,and analysed mechanics features and effect factors. 介紹了在立式巷道支架試驗台上,對不同結構形式平頂形柱腿可縮金屬支架的試驗結果。分析了支架的力學特徵和影響柱腿可縮性的因素。
- However, it may be more economical to cut mass-terminated cables in half and hardwire the individual wires to the test fixture. 然而,若將接線頭電纜分為兩部分,然後將獨立的導線硬連接至夾具,則更加經濟。
- The Model 8009 employs a safety interlock to prevent the high voltage from being applied to the electrode until the test fixture lid is closed. 8009型採用了一種安全互鎖機構,在測試夾具的蓋子關閉之前,高電壓不能施加到電極上。
- Can be used for probe board and loading board of ICT、ATE and different kinds of functional test fixture, AOI plate fixture and other anti-static fixture or equipment. 用作ICT/ATE測試夾具針板、載板、各種功能測試夾具的針板和載板,以及AOI拖板治具和各種抗靜電要求較高的治具或者設備。
- From the control box, burning me, burning lights, electromagnetic valve, high-pressure ignition, plastic goods test fixture, gas pipes and signal the line of control components. 由控制箱、燃燒箱、燃燒燈、電磁閥、高壓點火器、塑料試品夾具、煤氣管和信號控制線組成。
- If you are using a test fixture, keep the lid closed while power is applied to the device under test. Safe operation requires the use of a lid interlock. 如果使用測試夾具,當被測電路加有電源時,請保證外蓋安裝完好。為確保操作安全,需要使用一個外蓋聯鎖。
- Oxygen gas transmission rate ( O2 GTR ) is determined after the package has been mounted on a test fixture and has equilibrated in the test environment. 氧氣透過率(O2 GTR)是將包裝物固定在測試裝置上並在測試環境中達到平衡后測定的。