您要查找的是不是：
- Parting line at the acceptable surface. 合模分佈在合理可接受的表面。
- Parting line cleared and released properly? 分模線是否正確?
- Parting line locks are required on all molds. 瑣模塊所有的模具都需要。
- The sides are sectioned with a vertical parting behind each ear. 邊與垂直一起區段在每隻耳朵後面分開。
- The parting line tolerance for gib installation is +.000/-.002. 安裝導板的分模線公差為+.;000/-
- Moulding machines, Moulding line, Vertical parting automatic shooting moulding line, Horizontal parting stripper shooting moulding line, Sand preparation system Resin sand line, Silicate-bonded sand line. Shot blaot cleaning equipment, Surface. 造型機,造型線,垂直分型、水平分型自動造型線,砂處理成套設備,樹脂砂、水玻璃砂成套設備,中英合資拋丸清理機、表面強化設備。
- Now, subsection the right side with three vertical partings. 現在,小部份和三垂直的分別正確的邊。
- An annular groove is at the outer surface of the insulated loop frame,which requires a vertical parting of the mould along the axis. 線圈絕緣框外側有一圈凹槽,要求成型模具沿軸線垂直分型。
- When they erupt, diamonds are thrown out of the top in the lava or are left in the pipe, the central, vertical part of the volcano. 當火山爆發時,鑽石被拋到熔岩的上部或者留在火山中部豎直的熔岩通道中。
- There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 產品的這個位置不能出模,我們打算做行位,在此面上會有分模線,你接受嗎?
- Becasue of hand deflashing, please mark the parting line into the drawing, and please let me know then the flash size. 因為手遮光，請將分界線在圖中標出來，並告訴確切尺寸。
- The vertical line meets the horizontal one here. 垂直線與水平線在此相交。
- Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate part line locks. 上、下模需要精確配合或有擦位的地方,模具一定要有直身鎖。
- Follow this by subdividing the remaining parting at the front-left side of the diamond with three vertical partings. 藉由在和三垂直的分別鑽石的前面留下的邊細分剩餘的分別跟隨這。
- The parting line at ends of block should be designed such that any offset is in 1"increments for maintenance purposes on core. 考慮到動模維護需要,封膠面應有1」左右的偏移增量。
- Our company produce grey cast iron, ductile cast iron and other cast iron, for refrigerator compressor, ai conditioner compressor, automobile, underground, hydraulic and so on, by DISA vertical parting molding, permonent mold and other casting processes. 採用DISA垂直分型無箱射壓造型、金屬型等鑄造方法,專業為製冷、汽車、地鐵、液壓等行業生產精細鑄鐵件。
- After subsectioning the fringe at the recession on either side, move to the left side section and subsection with three vertical partings. 在在任一邊上的後退小部份邊緣之後,以三垂直的分別移到左邊的旁區段和小部份。
- The optimization parting direction was determined after all undercut features were distinguished, and the parting line and parting surface were confirmed accordingly. 通過側凹特徵的判別確定模具的優化脫模方向，並確定模具的分型線和分型面。
- Subdivide three vertical partings and sculpt alternately short, long and short lengths using 90 degree projection and a vertical finger position. 細分三垂直的分別而且雕刻交替短，長的和短長度使用90度發射和一個垂直的手指位置。
- The selection of parting line,the determination of round sprue runner diameter,the design of round sprue runner shape and pouring gate form were presented. 介紹了模具分型面的位置選擇、圓形流道直徑的確定、圓形流道形狀的設計、澆口形式等。
