您要查找的是不是：
- Ultimate load designs according to the yield-line or strip methods do not guarantee safety against cracking or excessive deformation. 接屈服線法或條帶法的極限荷載設計不能完全保證抗裂或防止過度變形。
- The paper analyzes influence of hanger component weight and load design method for pipe node movement,node restraint load,node code stress and pipe system modal frequency. 本文通過大量的計算,分析了支吊架零部件重量及吊零方式對管道位移、載荷、應力、模態頻率和彈簧型號的影響。
- This study suggests a admissible load designing method, which leads out a series of calculating formulas based on the parabola theory and works out a value table for loaded rope to establish a systematic admissible load designing method. 本文提出許用荷重設計法,在拋物線理論的基礎上推導出一系列計算公式,編製承載索數值表,建立起系統的許用荷重設計方法。
- ultimate load design 極限載荷設計,極限荷載設計
- The ultimate load of plate girders was analyzed by spline finite strip and plastic hinge method. 摘要用樣條有限條塑性鉸法分析了板梁的極限荷載。
- This paper describes the design method of broad band coaxial termination load. 本文敘述了寬頻同軸終端負載的設計方法.
- The method for analyzing ultimate load capacity of steel curved beam with degenerated three-dimensional solid virtual laminated beam element is presented. 提出採用三維實體退化虛擬層合梁單元計算鋼曲梁極限承載力的方法。
- In this paper the state of the art has been made, at last the method of finite element has been put forward for the ultimate load of RC beams with exposed tensile reinforcement. 介紹了國內外研究現狀，對各階段的研究成果進行了綜合分析與評價，最後提出用有限元方法計算受拉鋼筋暴露的混凝土梁的承載力。
- The CDU design method on VAPS is given. 在滿足真實性和可靠性的前提下,給出了基於VAPS的CDU設計方法。
- But their design method is still in groping stage. 但變螺距誘導輪的設計方法還在摸索階段。
- Design method for the confinement is effective. 同時說明了該設計方法的有效性。
- The in-plain ultimate load carrying capacity of concrete filled steel tubular(CFST) laced columns compressed eccentrically is calculated based on design guidelines for CFST structure. 應用鋼管混凝土結構設計規程,對鋼管混凝土格構柱偏心受壓試件進行面內整體承載力計算。
- The experimental results indicate that the ultimate load decreases with increase of perforation size. 根據不同開孔尺寸試件的試驗結果可知，開孔構件的極限承載力隨著開孔高度、寬度的增大而下降。
- Thus, a successful muffler design method is developed. 探索了一種消聲器的設計和模擬分析方法。
- Vesic A S.Analysis of ultimate load on shallow foundation[J].Proc ASCE,1973,99(SM1). 李進軍;黃茂松;史三元;杜海金.;複合地基樁土應力比與褥墊層厚度關係的試驗研究[J]
- Based on layered-shell element method,ultimate loads of reinforced concrete multi-T girders are calculated. 基於分層殼元法,對鋼筋混凝土多梁式T梁的極限承載力問題進行了研究。
- Formulas for estimating ultimate load of WMM/SB strengthening columns were given in the thesis. 結果表明，被加固試件的保護層能與核心混凝土共同工作到最後，不出現大片剝落。
- A VM-Based design method for embedded memory system. 基於虛擬存儲的嵌入式存儲系統的設計方法。
- Formulas for predicting ultimate load of WMM strengthening column were provided. 並給出鋼絲網砂漿加固素混凝土柱的極限承載力公式。
- Here we utilize the traditional skid-to-turn (STT) design method. 接著將自動駕駛儀代入非線性模式，觀察其模擬結果。
