您要查找的是不是：
- Verticality of track and wheel should more than 999/1000.The center distance of wheels is 5835mm and the relative difference of it is no more than 1mm. 輪對軌間的不垂直度不得大於1/1000,車輪順軌中心間距5835mm的相對差值不得大於1mm。
- The center distance of R/L crank between piston with cylinder concern the power of engine. 活塞與汽缸的間隙直接影響引擎運轉之特性，因此最佳的間隙值會使引擎產生最佳的馬力及燃燒的廢氣。
- Model : Defined by the center distance between shafts. The bigger the model number. The bigger the reducer structure. 型號:由減速機入力和出入之中心距而定，型號越大，減速機體積越大。
- Dies seat: Adopt West Germany technology (Inlay type), assure the drawing center distance to avoid the wire breakage. 模座：採用西德技術（鑲入式），保證拉伸的中心距，減少斷線機率。
- KT-series is as the same as ZT-series and its principle is adjusting the center distance of roller-sting to welding the weld material of different diameter. KT系列產品與ZT系列產品相同，工作原理是人工調正滾輪架的中心距，以適應不同直徑焊接體的焊接。
- When the center distance of two involute gears is fixed, the plane higher pair composed by them will introduce one restriction to the mechanism. 摘要當參與嚙合的兩個漸開線齒輪之間有固定的中心距時，其構成的平面高副引入一個約束；
- You must enable Message Tracking Center on each server for which you want to track messages. 必須在要跟蹤其郵件的每一台伺服器上啟用郵件跟蹤中心。
- The change of center distance due to non-conjugate of corrugating roller in molding corrugated board process was discussed. 摘要論述了瓦楞輥在成型瓦楞紙板過程中，由於瓦楞輥的齒形是非共軛齒廓，中心距是變動的。
- Ship hull's sagging and hogging may cause center distance increasing or reducing to longitudinally disposed gear housing. 船體中垂及中拱彎曲變形會使沿船體縱向布置的齒輪座中心距產生增減。
- The center distance of the roller on the cradle draft assemble greatly affects the yarn eveness, hairiness and ends breakage. 摘要牽伸裝置上羅拉的中心距及其定位對成紗的條幹不勻率、毛羽、斷頭都有較大影響。
- For unknown class label samples set，an unsupervised feature selection algorithm based on center distance ratio principle is proposed. 針對未知類標號的樣本集，提出基於中心距離比值準則的無監督特徵選擇演算法。
- Calculates the coordinates of the spindle and drive shaft and checking the center distance, determined department spindle must use dislodges the gear. 計算主軸、傳動軸的坐標並進行中心距驗算，確定部分軸上需採用變位齒輪；
- In order to avoid the 「midconvex」 of tooth profile and the serious abrasion in dedendum, the technology of center distance variation was adopted. 為了避免出現齒面「中凸」及齒根部研磨較嚴重的現象，採用了變中心距研齒工藝。
- The product output to sprain torque ,which make gears the least load and (with the equal center distance)can inproue more 30% bearing capacity than the traditional load capacity. 本產品為輸出升扭，使各檔輪所受載荷減小，相同中心距較傳統結構提高承載能力30%25以上。
- Our pilotless rocket enters the track of the earth. 我們把一個無人駕駛的火箭送入了地球的軌道里。
- The article introduces the calculation equation of how the gauge sets up and calculates the roller center distance which is of guiding signification to cotton mills and cradle manufacturers. 文章介紹了搖架上羅拉隔距規設定隔距的計算公式的推導過程，對棉紡廠、搖架製造廠具有指導意義。
- This rough track will soon be a metalled road. 這條坑坑窪窪的路不久就要鋪上碎石了。
- I'm trying to track down my old Aunt Maud. 我正試圖尋找到我那年邁的嬸嬸莫德。
- The cyclist went at full sail along the track. 自行車手沿著跑道全速前進。
- Bill has a feeling he is on a fast track. 比爾感覺到他正快速邁向成功。
