您要查找的是不是:
- It can increase the hole inclination angle range and drill elevation angle holes, while setting the top drive power head and hole top plate toward the opposite direction. 動力頭及孔口板調轉方向,可直接鑽鑿仰孔,大大增加鑽孔傾角範圍。
- The top plate dismantling beforehand system in cast-in-place shear wall structure provides a practical method. 而現澆剪力牆結構頂板早拆體系為解決這些問題提供了一個可行的方法。
- Automatic tracking the cutting speed: do not need to change the cutting angle if the glass ribbon speed changed. 切割速度自動跟蹤:玻璃帶速度發生變化,不需要改變切割角度。
- By appending a support board at thebottom of top plate in worktable, the whole rigidity is improved. 在工作台上板的下端增加了支撐板,使整體剛度得到了提高。
- In the paper sliding-cutting angle and cutting angle were calculated,other major cutting parameters were given. 文中計算了滑切角,切割角等主要切割參數,給出了新型剖半機的主要技術參數。
- Abstract: The top plate of basement of Shenzhen West Red-tree Project was designed as a planted and impounded roof. 摘要:深圳紅樹西岸工程地下室頂板空中花園設計為種植及蓄水屋面。
- At the time Influences of cut angle in indicated power, COP and discharge temperature is studied in details, too. 同時還詳細分析和研究了排氣通道上斜切口角度對壓縮機製冷量、輸入功率、性能係數、排氣溫度等的影響 ,為滾動轉子式壓縮機的優化和性能提高奠定基礎
- If you notice that the top plate is slightly warped in a downward fashion along the edge adjacent to the armboard, this is normal. 播放以前聽過多次的唱片,整個聲音發生了明顯的變化,聲音的質感提高不少,小提琴的運弓力度和琴箱的共鳴聲明顯加強,那種聲音是自己非常喜歡的。。。
- The expressions of dihedral angle and cutting angle of the intersecting groove are deduced by way of space analytical geometry. 利用空間解析幾何原理推導了多管、板相貫坡口的兩面角和實際切割角的表達式,建立了切割多管、板相貫坡口的數學模型。
- Today, the market again in the 7th by hailun line support, quick upside afternoon, the final is still close at a red disc, coal or the top plate. 今天大盤再次在7號操盤線受到了支撐,午後快速上攻,最終仍然以紅盤報收,煤炭板塊漲幅靠前。
- A quartz crystal has crystallographic axes, and crystal cut is defined according to the cutting angle against a crystallographic axis and its associated mode of vibration. 溫頻特性與切割角有關,每個石英晶體具有結晶軸,晶體切割是按其振動模式沿垂直於結晶軸的角度切割的。
- Using the programmable controller in the automobile rear axle house ring stiffener,logic sequential control was realized in the top plate automatic welding craft. 採用可編程式控制制器在汽車後橋殼加強環、后蓋自動焊接工藝中實現邏輯順序控制。
- The influence of air cutting angle and air cutting time to chip breakage is studied quantitatively.The correctness of air cutting theory is verified by the experiments. 定量分析了間斷切削過程中的空切角度、空切時間對斷屑的影響,並通過試驗驗證了用空切理論分析斷屑的正確性。
- The top plate is stressed when fitted into the wooden plinth, for better resonance control, and transmission of unwanted energy.You are now ready to set up the suspension. 在兩位大蝦的指導下,悟出了一個道理,任何系統的聲音沒有對和錯,只有自己喜歡與否,耳朵收貨:)在此感謝兩位大蝦的指教。
- The reasonable ranges of the geometrical parameters are given by analyzing the influences of the vertex angle and cutting angle on impact force and penetration displacement. 通過分析稜柱桿的幾何參數對撞擊力和侵入位移的影響,給出了稜柱桿主要幾何參數的合理範圍。
- Summary: Numerical control cutting line used in opening and plating cutting coil into exact size sheet and stowing. 橫剪線概述:數控板開卷校平剪切線,主要用於將卷板進行開卷、校平、切邊、精密定尺剪切成各種規格的板材,並整齊堆垛。
- An experimental IR thermographic method for the evaluation of surface temperature distribution of the top plate is adopted to show the convective heat transfer effects of nanofluids. 藉由紅外線熱影像實驗方式來探討流道內奈米流體強制熱對流現象對盤面溫度分佈之影響。
- Substantial experience in CNC plates cutting and Robot Profile Cutting such as Programming, Production, Logistics and Workshop Organization and Management. 具有CNC板材切割和機械手仿形切割的設計、生產、後勤和車間的組織和管理方面的豐富經驗。
- Due to its relative small losses, theoretically it is supposed to get 50% of conversion effi. ciency at a pump level of 600 mW by using a BBO crystal with cutting angle of 27.030 and length of 10mm. 從分析其性能出發通過計算指出,使用BBO晶體獲得倍頻426nm藍光(切割角度為27.;430,長度為10mm),雖其非線性轉換係數小,但由於該晶體的損耗小,在泵浦功率約為600mW時。 理論上同樣可以得到50%25的倍頻轉換效率。
- I used scrap Lexan to hold the plates in the jaws of a Vice-Grip.Dimple the top plate of the stack at the center of the hole. 製作動片組的接觸片, 切下一長條防水板,其長度應足夠長,能覆蓋到動片組軸孔兩側。