您要查找的是不是:
- Further opening the throttle valve activated the main fuel jet. 當節流閥進一步打開時,主噴口開始工作。
- Air inlet throttle valve with pneumatic actuator and positioner. 空氣進氣節流調節閥:帶有氣動定位和執行機構。
- The adjusting of screw prevents the throttle valve from moving to the fully closed position. 調節螺釘防止節氣門運動到全關閉位置。
- Finally, an appropriate throttle valve was chose to serve the superfluid helium system. 最終確定了一個適合該超流氦系統的較為理想的節流閥。
- A throttle valve control device is composed of a stator core with a solenoid and a rotor carrying a throttle valve. 一種節流閥控制裝置,包括一個帶螺線管的定子鐵芯和一個帶節流閥的轉子。
- Enough air-found mixture can seep around the throttle valve and through the idle system to maintain the dieseling. 圍繞在節氣門處有足夠的空氣燃料混合氣經怠速系統泄漏過來助長了熄不了火現象。
- Reduced pressure near the partially closed throttle valve caused the fuel to flow from the idling jet into the intake air. 由於部分關閉的節流閥附近的壓力下降,燃油由怠速噴口噴入吸進的空氣。
- The sleeve also rises up the shaft, and when it rises beyond a certain point, it operates a throttle valve lever, and so reduces the flow of steam. 套筒也隨之順軸上升。而當套筒升過一定的點時,套筒就會帶動一個節流閥的閥桿進入工作,這樣就能減少蒸汽的流量。
- Whereas, the optimal heat rejection pressure in the expander cycle is different from that of in the throttle valve cycle. 但是,膨脹機循環的最佳高壓壓力與節流閥循環的最佳高壓壓力不同。
- When the compressor and the expander efficiencies are given, the optimal heat rejection pressure in the CO2 throttle valve cycle is greater than that of in the expander cycle. 當壓縮機和膨脹機的效率一定時,CO2節流閥循環的最佳高壓壓力比膨脹機循環的高。
- Weighing hopper is lodged on 3 load cells. The amplifier, feeding device with dust collar, magnetic vibrator, pneumatically operated throttle valve shutter are included. 稱重倉帶有3個感測器。系統包括:放大器、進料裝置和收塵包、振動器、放料氣閥。
- Through fuel pumps,plus a throttle valve of statistical instruments,minus contained,thus allowing detection instruments in different load performance parameters. 通過油泵、節流閥對被測機具進行加、減載,從而可以檢測機具在不同載荷下的性能參數。
- In the exploration and development of high-pressure reservoirs, many dangerous cases even accidents of blowout happen because of the throttle valve failing. 在高壓油氣藏的勘探開發中,多次因節流閥失效而發生井噴失控險情,甚至導致井噴事故。
- The application and working process of throttle valve in injection mold of unbalanced cavities were introduced,and the key points of designing throttle valve was analysed. 介紹了節流閥在非平衡型腔注射模中的應用及模具工作過程,並分析了節流閥的設計要點。
- A systematic study was performed on the extruder set via analyses of the factors such as feeding, screw speed, throttle valve, screen pack changer, die plate and pelletizer, aimed at saving energy. 選擇進料狀況、螺桿轉速、節流閥、換網器和模板及切粒機等因素對擠出機機組的影響進行了系統分析、研究,發現這些因素對擠出機的負荷和能耗影響較大。
- The carbon-dioxide swinging rotor expander was designed and developed to replace the throttle valve in order to reduce the loss of throttling. 摘要設計開發了二氧化碳擺動轉子膨脹機,代替節流閥減小節流損失。
- stacked unidirectional throttle valve 疊加式單向節流閥
- stacked double directional throttle valve 疊加式單向節流閥
- Cause analysis of the water cooled wall tube burst focused on irrational points of design,excessive thermal loading,changes of coal category,burner defects and deposits in throttle valves. 著重從鍋爐設計不合理、熱負荷過高、煤種變化、燃燒器的缺陷及節流閥結垢等方面分析了水冷壁爆管的原因,指出必須進行鍋爐改造。
- BOWDEN CABLE PULLEY FOR THROTTLE VALVE 節氣門拉索滑輪