您要查找的是不是:
- How can it pass the pre-installation self test? 能通過安裝前的測試嗎?
- Fixed function for routine test mode. 常規試驗模式固化功能.
- Under test mode, you run each step individually. 在測試模式下,可以單獨運行每個步驟。
- The fixed gas detection system with automatic self test. 具有自我自動校正功能的固定式氣體偵測系統.
- The fips driver can't load. The driver failed the algorithm self test. fips驅動程序不能載入。此驅動程序的演算法自檢測失敗。
- Press the Esc key or close the dialog box to end test mode. 按Esc鍵或關閉對話框以結束測試模式。
- Using Bluetooth Test Mode for Transmitter Test and Physical level Observe. 藍牙測試模式實現及其物理層觀測。
- Once rebooted the PDT should be clear,unless the system actually finds some me?mory problem when doinga self test. 重新啟動后,PDT應當空白,除非系統在自檢上確實發現有內存問題。
- Patented Vaginitis Self Test Card provide free of charge can be used for genital health cheek. 贈送陰道炎自我女性腎虛如何調理檢測卡,對生殖器健康進行定性檢查。
- TEST MODE: The solenoid is energized with a fixed duration pulsSubsequent fixed pulses occur when the diaphragm reaches the switch closure point. 測試模式:用一個固定的持續脈衝激活電磁閥。當橫膈膜達到開關關閉點時,隨後出現固定脈衝。
- Automatic moment limiter has the function of self testing and alarming. 全自動力矩限制器具有自動檢測和報警功能。
- With the fast growing portable electronics market and higher need of wafer test, power consumption problem of built in self test (BIST) has attracted more and more considerations. 隨著手持設備的興起和晶元對晶片測試越來越高的要求,內建自測試的功耗問題引起了越來越多人的關注。
- No matter how the dialog box will behave at run time, you can terminate it in test mode by pressing ESC. 不論對話框在運行時的行為如何,您都可以通過按Esc鍵在測試模式下終止它。
- If you want to run the step for testing, you must promote it to test mode. 如果需要運行這一步驟來執行測試,則必須將該步驟升級到測試模式。
- When you promote the step to test mode, the Data Warehouse Center creates the target table. 當您將這一步驟升級到測試模式時,Data Warehouse Center就會創建目標表。
- Capable of operating various machine tools, can read drawings.Loading mode.With mold, to an independent test mode. 能操作各種加工機床,能看懂圖紙.;裝模
- This paper presents a segment weighted random built-in self test (SWR-BIST) technique for low power testing. 本篇論文提出了區段加權亂數之低功率自我測試技術。
- Therefore, after you promote a step to test mode, you can make only those changes that are not destructive to the target table. 因此,當您將一個步驟升級到測試模式之後,就只能進行那些不會損壞目標表的修改。
- Function The Pulser Preamplifier can be programmed to inject a sine wave, for the purpose of automated self testing or calibration. 結構脈衝發生器/前置放大器可用程序控制繪製正選波;目的是進行自動化自我監測和校正.
- The Functional Test Mode was also selected so that the full IFX-encoded response was captured in the test results managed by the. 管理的測試結果中捕獲完整的IFX編碼的響應。