您要查找的是不是：
- The strength, stiffness and mode shape of the rear axle housing was calculated via finite elemant methool (FEM). 根據計算結果分析，指出了其結構存在的缺點，提出了改進方案。
- The analytical findings provide some referential basis for the designof a rear axle housing structure. 研究結果為橋殼結構設計提供了一定依據。
- In order to reduce gas hole defects in the rear axle housing castings,oddside venting system was used. 為解決汽車後橋外殼鑄件存在的氣孔缺陷,采了假型排氣系統。
- Remove differential case from axle housing. 從軸管上拆卸差速箱。
- Remove differential case and dummy bearings from axle housing. 拆卸軸殼內的差速箱和平衡軸承。
- Aiming at laggard and low automatization degree of clearance measure method on axial assembly clearance between half shaft assembly and rear axle housing in automotive rear axle assembly, a new type clearanceometer was developed. 針對汽車後橋總成中半軸總成與後橋殼之間軸向裝配間隙測量方法落後、動化程度差等問題,開發了汽車後橋總成裝配間隙測量儀。
- The 194 Rear Beam-design Iron (RBI) axle housing has an iron center casting (differential housing) with axle shaft tubes extending from either sidThe tubes are pressed into and welded to the differential housing to form a one-piece axle housing. 194後梁設計鋼（RBI）軸殼有一個帶有驅動軸套的鋼製的中心鑄件（差速殼），它延伸到兩邊。軸套被壓進差速殼，並焊在差速殼上，形成了一個整體的軸殼。
- The allowable strength, static strength, fatigue life and load-carrying capability of hydro-bulged rear axle housing in a 0.75 t truck are analyzed using FEA software ANSYS and the variation rule of its strength is obtained. 摘要以0.;75t貨車液壓脹形橋殼為例，利用有限元分析軟體ANSYS對其許用強度、靜強度、疲勞強度（壽命）及其承載能力進行分析，得到液壓脹形橋殼強度的變化規律。
- Using the programmable controller in the automobile rear axle house ring stiffener,logic sequential control was realized in the top plate automatic welding craft. 採用可編程式控制制器在汽車後橋殼加強環、后蓋自動焊接工藝中實現邏輯順序控制。
- Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts. 在軸殼內（沒有墊片）安裝差速箱和模型軸承，並緊固固定帽螺栓。
- Rear Axle Housing Assy of Automobile 汽車後橋殼總成
- The analysis provides a reliable reference for the optimal design of a hydro-bulged axle housing. 研究為液壓脹形橋殼優化設計提供可靠的參考。
- Drive shafts modified for new location on the axle housing and because of the new doubler. 傳動軸修改來配合分動箱放大齒輪組。
- The first axle housing type is a unitized carrier construction, commonly referred to as a Salisbury or Spicer type axle assembly. 第一橋殼型是一個單元載體建設，通常稱為梳士巴利或斯派塞類型橋總成。
- There are 12 round holes circumferencially equispaced on the axle housing cast,being in need of radial multiple core pulling. 軸套鑄件上有12個周向均布的圓孔,壓鑄生產時需要多型芯徑向抽芯。
- Unitized carrier axle housing constructions of this type are economical to manufacture and are readily adaptable for a variety of vehicles. 組合承運人車軸住房建設這類經濟生產，並易於適應各種車輛。
- Through the drive axle housing , the tractive force 、 braking force and lateral force act on the wheel transfer to the suspension system 、 frame or carriage. 作用在驅動車輪上的牽引力、制動力和側向力,也是經過橋殼傳到懸挂及車架或者車身上。
- Strength Analysis on Hydro-bulged Automotive Rear Axle Housing 液壓脹形汽車橋殼強度分析
- A body of the enemy hung upon their rear. 一夥敵人緊緊地跟在他們的後面。
- Drilling machine for rear axle house flange 後橋殼法蘭鑽孔
