您要查找的是不是:
- oil pressure relief valve spring 油壓安全閥簧
- Due to the release of pressure when removing the cover, the relief valve spring may eject quickly. 因為在拆卸閥蓋時鬆開壓力,安全閥彈簧可能會快速彈出來。
- Install the high pressure relief valve in the compressor manifold fitting. 在壓縮機歧管配件里安裝高壓釋放閥。
- Install a 125 PSI pressure relief valve in the cold water supply line. 在冷水供應管道上安裝一個125psi的減壓安全閥。
- Must be installed to allow complete drainage of both the temperature and pressure relief valve and the discharge line. 必須正確安裝,使得降溫減壓安全閥和排水管道都能夠完全排泄。
- Remove the relief valve cover, stem/diaphragm assembly, and relief valve spring. 拆卸安全閥閥蓋,閥桿/隔膜總成,和安全閥彈簧。
- Temperature and Pressure Relief Valve is required, but may not be factory installed. 需要降溫減壓安全閥,但可能不在工廠安裝。
- Note: The installation of a separate pressure relief valve is necessary for installations using gas shutoffs. 注意:採用燃氣關閉閥,有必要安裝獨立的壓力安全閥。
- By doing so, the DET keeps the system pressure below the relief setting of the Temperature and Pressure relief valve. 通過這種功能,det系列將系統壓力保持在溫度壓力安全閥的排放設置下。
- It can simplify the fire supply system of highrise building by applying pressure relief valve to vertical compartment. 採用減壓閥對高層建築物的消防給水系統進行豎向分區 ,可以簡化系統。
- An ASME Section IV certified pressure relief valve shall be installed on each boiler as noted. 正如以前所提到,每個鍋爐都應該安裝一個ASME第四節認證的壓力安全閥。
- spring loaded pressure relief valve 彈簧載入的壓力泄放閥
- Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler working pressure. 每個熱水供暖鍋爐都必須配置壓力安全閥,其設置的泄壓壓力必須小於鍋爐的最大工作壓力。
- Remove the relief valve spring. 拆卸安全閥彈簧。
- DO NOT tamper with the electronic control board, temperature sensors, heating elements, electrical connections, or temperature and pressure relief valve. 不要篡改電氣控制板,溫度感應器,加熱元件,電氣連接,或降溫減壓安全閥。
- Temperature and pressure relief valve properly installed with a discharge line plumbed to an open drain and protected from freezing. 正確安裝降溫減壓安全閥,並配置排泄管引導至一個敞開的排水口,並確保不會被凍結。
- Temperature and pressure relief valve properly installed with a discharge line run to an open drain and protected from freezing. 正確安裝降溫減壓安全閥,並配置排泄管引導至一個敞開的排水口,並確保不會被凍結。
- NOTE: 15" diameter chambers are standardly furnished with a pressure relief valve, factory set at 60psi to protect the chamber from excessive pressure. 註:在壓力安全閥上,15英寸直徑的腔室室標準配置,工廠設置是60psi,以保護腔室不會出現壓力過大現象。
- Periodic discharge of the temperature and pressure relief valve may be due to thermal expansion in a closed water supply system. 在一個封閉的水供應系統中,熱膨脹可能導致降溫減壓安全閥的周期性排泄。
- In order to prevent misuse, and some special pressure relief valve and the special connection between the cylinder mouth. 為了防止誤用,有些專用減壓閥與鋼瓶之間採用特殊連介面。