您要查找的是不是:
- Install the high pressure relief valve in the compressor manifold fitting. 在壓縮機歧管配件里安裝高壓釋放閥。
- For pressure relief you turn the opening valve against clockwise direction. 壓力釋放時,逆時針旋轉開口閥。
- Install a 125 PSI pressure relief valve in the cold water supply line. 在冷水供應管道上安裝一個125psi的減壓安全閥。
- Pressure relief devices protect storage tanks against overpressure hazards, you must know their set points. 壓力釋放裝置用於防止超壓的危險,你必須清楚它們的設定值。
- Do not walk on the top surfaces of the Powerbloc panels, rupture points for pressure relief. 不要在開關櫃瀉壓頂板上行走。
- Must be installed to allow complete drainage of both the temperature and pressure relief valve and the discharge line. 必須正確安裝,使得降溫減壓安全閥和排水管道都能夠完全排泄。
- Building valves - Combined temperature and pressure relief valves - Tests and requirements. 建築閥門。溫度和壓力組合安全閥。試驗和要求。
- Temperature and Pressure Relief Valve is required, but may not be factory installed. 需要降溫減壓安全閥,但可能不在工廠安裝。
- Note: The installation of a separate pressure relief valve is necessary for installations using gas shutoffs. 注意:採用燃氣關閉閥,有必要安裝獨立的壓力安全閥。
- Use regulators and pressure relief devices when connecting cylinders to circuits having lower pressure service ratings. 當把鋼瓶連接到較低額定工作壓力的迴路上時,要使用調整器和減壓裝置。
- You must make provisions for pressure relief protection of your plumbing system and components. 此時就必須採取措施進行壓力釋放,以保護管道系統和部件。
- By doing so, the DET keeps the system pressure below the relief setting of the Temperature and Pressure relief valve. 通過這種功能,det系列將系統壓力保持在溫度壓力安全閥的排放設置下。
- Therefore, the spacecraft must have a facility with "pressure relief" feature and restore function. 因此,航天器上必須有一個設施具有「泄壓」功能和恢復功能。
- Study on the relief door in by- pit 煤礦副井安全門的研究
- Multiple pressure relief devices are installed on these tanks to protect against overpressure. 在這些儲氦罐上安裝了多樣減壓裝置,以防止過壓。
- It can simplify the fire supply system of highrise building by applying pressure relief valve to vertical compartment. 採用減壓閥對高層建築物的消防給水系統進行豎向分區 ,可以簡化系統。
- An ASME Section IV certified pressure relief valve shall be installed on each boiler as noted. 正如以前所提到,每個鍋爐都應該安裝一個ASME第四節認證的壓力安全閥。
- Each hot water space heating boiler shall be equipped with a pressure relief valve set to relieve below the maximum boiler working pressure. 每個熱水供暖鍋爐都必須配置壓力安全閥,其設置的泄壓壓力必須小於鍋爐的最大工作壓力。
- DO NOT tamper with the electronic control board, temperature sensors, heating elements, electrical connections, or temperature and pressure relief valve. 不要篡改電氣控制板,溫度感應器,加熱元件,電氣連接,或降溫減壓安全閥。
- Temperature and pressure relief valve properly installed with a discharge line plumbed to an open drain and protected from freezing. 正確安裝降溫減壓安全閥,並配置排泄管引導至一個敞開的排水口,並確保不會被凍結。