您要查找的是不是：
- The bore and outside diameter tolerances of SKF single and double direction tapered roller thrust bearings are produced, with very few exceptions, with Normal tolerances to ISO 199-1979. SKF單向和雙向圓錐滾子推力軸承的孔徑和外徑公差除少數例外,均按照ISO 199-1979標準的普通級公差生產。
- Collars-Inside and Outside Diameters Tolerance Selection Type 金屬軸環-內外徑公差選擇型
- The eccentric diameter tolerance which is h9. 偏心直徑公差為h9。
- Single plane mean outside diameter deviation. 單一平面平均外徑偏差。
- Remark: Consult order for special outside diameter. 注:特殊外徑需協議訂貨。
- Check the outside diameter of stabilizers. 檢查扶正器的外徑。
- A 3/4" NPT pipe thread has an outside diameter - OD - of 1.050 inches. 例如：一個標準為3/4"NPT的管外部直徑為1.;050英寸。
- Grinding wheel outside diameter thickness and bore may be customer specificied. 砂輪外徑、厚度、孔徑可依客戶需求指訂尺寸。
- The cam-bores may present a roundness error within the diameter tolerance, so the most significant diameter value for the shim/tappet thickness determination is the one along the valve train axis. 凸輪孔可能會出現直徑公差範圍內的誤差，所以決定墊片/凸子厚度的最大直徑值應位於氣閥機構的軸部。
- In the past, Thinnet coaxial cable with an outside diameter of only 0.35 cm was used in Ethernet networks. 在過去，外圍直徑僅0.;35公分的細同軸電纜被用在乙太網路。
- The control accuracy of inside &outside diameter is very high,suitable for various splices. 內外徑尺寸精度控制高，適合各種接頭。
- Subsequently, the effective area was demarcated manually, and rolling bearing outside diameter character was distilled. 接著採用區域人工標定，進行滾動軸承外徑的特徵提取。
- To make sure that the bearings are correctly mounted, a "V" is marked across the outside diameter of the bearing pair (fig 8d). 為了確保軸承的正確安裝,在配對軸承的外徑上標有「V」(圖8d)。
- The shank diameter tolerance which is h7, and, 芯柱體直徑公差為h7
- In my setup I used aquarium air pump tubing (6 mm outside diameter) for the manometer (pressure gauge) although it results in a small capillary error. 在我製作的裝置中,使用魚缸的空氣泵管路(外徑6 mm)作為壓力表(壓力計),儘管它會導致小的毛細管誤差。
- Diameter tolerance of steel wire 鋼絲直徑
- Mini Rods-Outer Diameter Tolerance Fixed Type 小口徑棒材-外徑公差選擇型
- The outside diameter of copper tube shall be tested by Micrometer. The tooth depth and the bottom wall thickness shall be tested by Microscope. 外徑尺寸用外徑千分尺測量.;齒高和底壁厚用雙目倒置小金相測量。
- Description: Type GC-A is a roller type freewheel non-bearing supported.Nominal outside diameter is a standard ball bearing dimension. 系列為無軸承支撐滾柱式單向離合器，外部尺寸與標準軸承尺寸相同。
- LH-PL series of spray cooling box mainly used for supplementary cooling pipes to ensure the accuracy of pipe outside diameter size. PL系列噴淋冷卻箱主要用於管材的補充冷卻以確保管材外徑尺寸的準確性。
