您要查找的是不是:
- Parting line at the acceptable surface. 合模分佈在合理可接受的表面。
- Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate part line locks. 上、下模需要精確配合或有擦位的地方,模具一定要有直身鎖。
- Parting line cleared and released properly? 分模線是否正確?
- Parting line locks are required on all molds. 瑣模塊所有的模具都需要。
- Lack of consistent and reliable mould tool makers prompted ITL to set up its own toolmaking capability at its Ipoh facility. 由於缺少長期和可靠的模具製造商,這就促使ITL公司在怡保的生產廠家建立了公司自己的模具製造廠家。
- The parting line tolerance for gib installation is +.000/-.002. 安裝導板的分模線公差為+.;000/-
- Make programs and operate EDM and manufacture tool parts. 編程並操作線切割機,及加工模具部件;
- There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 產品的這個位置不能出模,我們打算做行位,在此面上會有分模線,你接受嗎?
- Huangyan has become the important mould tooling center in China, and growing rapidly to export to the oversea market. 黃岩已成為中國重要的模具加工中心,而且增長迅速並遠銷海外。
- Becasue of hand deflashing, please mark the parting line into the drawing, and please let me know then the flash size. 因為手遮光,請將分界線在圖中標出來,並告訴確切尺寸。
- Design of Mould Tool of Impact Rolling Mo-Conductor 沖軋鉬導桿的模具設計
- The parting line at ends of block should be designed such that any offset is in 1"increments for maintenance purposes on core. 考慮到動模維護需要,封膠面應有1」左右的偏移增量。
- Tool parts for high impact such as hammer cheeks, planishing and gripper cheeks. Paper cutting knives, tobacco cutting knives, roll segments. 承受高壓力的工具部分,比如錘面、精軋夾面、制動器的制動面、裁紙刀、切煙刀、碾壓齒輪。
- Protects exposed machina tools parts from corrosion. 保護切削工具顯露部分;免受腐蝕.
- Application All machine tool parts, including bearings and gearboxes, lubricated by circulating systems. 用途可應用於各種機械工具內的潤滑油循環系統,包括軸承和齒輪箱。
- The optimization parting direction was determined after all undercut features were distinguished, and the parting line and parting surface were confirmed accordingly. 通過側凹特徵的判別確定模具的優化脫模方向,並確定模具的分型線和分型面。
- Operate high speed milling machine and make programs and operate EDM and manufacture tool parts. 操作高速銑床,編程並操作線切割機,及加工模具部件;
- The selection of parting line,the determination of round sprue runner diameter,the design of round sprue runner shape and pouring gate form were presented. 介紹了模具分型面的位置選擇、圓形流道直徑的確定、圓形流道形狀的設計、澆口形式等。
- Make programs and operate EDM and high speed milling machine and manufacture tool parts. 編程並操作線切割機和高速銑床,及加工模具部件;
- This soft tooled assy has been replaced by the hard tooled parts. 這個軟質的加工成型的組件已經被硬質的加工成型的部件所代替.
- 今日熱詞
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries