您要查找的是不是：
- Study of Press Forging Die Materials Optimization Expert System 壓力機鍛模具材料優化專家系統
- Design of a Composite Hot Forging Die for Screw Plugs. 油孔螺塞拼接式熱鍛模具的設計
- Sheet warm forming process, sheet warm hydroforming process and sheet press forging process are introduced in this paper. 介紹了鎂合金薄壁板材的溫熱衝壓成形技術、溫熱液壓成形技術和局部熱沖鍛成形技術。
- Abstract The paper gives out structure of tilting pin type hydraulic forging die for producing frame of shaker. 給出了震動器機殼斜銷式液鍛模具設計結構。
- Steel die forgings - Tolerances on dimensions - Part 1: drop and vertical press forgings. 鋼熱模鍛件。尺寸公差。第1部分:落錘鍛造和垂直壓力鍛造。
- Through the analysis of hook, a reasonable forging process and forging die have been designed. The defects has been analyzed and solved. 摘要通過對吊鉤的工藝分析，設計了合理的鍛造工藝方案及其熱鍛模，並對出現的缺陷進行了分析解決。
- Adapting to the characteristic and structure of mechanical press introduces implement method of parametric design for serial mechanical press product. 針對機械壓機的結構及其特點，介紹基於機械壓機系列產品參數化設計的實現方法。
- An investigation was carried out for the recondition of a mould for the forming of automotive plastic floor board and a half-axle swing forging die. 介紹了幾種典型模具快速修復工藝方法,並對汽車地板革成形模和汽車半軸擺動輾壓模的修復進行了研究。
- The compatibility of the mechanical press behaves as that of the pneumatic friction clutch and brake (PFC&PFB) which is a key component. 機械壓力機本身動作的協調性主要體現在其心臟部件氣動摩擦離合器與制動器(PFC&PFB)兩者動作的協調性之上。
- The dynamic stress concentration problems at the swallowtail on a hammer forging die are investigated by using the dynamic photoelastie method. 用動態光彈性法研究了錘鍛模燕尾的動態應力集中問題。
- It has concluded that the new hybrid mechanical press can satisfy multi-technique request from slider velocity characteristics in the course of process. 通過研究表明:這種新型混合輸入式曲柄壓力機可以滿足多種衝壓加工工藝對零件變形過程中速度變化特性的要求。
- The PLC control of JA21- 160 mechanical press is taken for example with S7- 200 CPU216 PLC,and the necessity of emulation for PLC control of the mechanical press is pointed out. 本文以西門子公司S7-200系列CPU216型PLC控制JA21-160型機械壓力機為實例，指出了對機械壓力機PLC控制進行模擬的必要性。
- Traditional forging die manufacturing including a lot of process and using EOM to form the impression results some disadvantages such as longer production time and higher cost. 摘要傳統鍛模加工，由於加工道次多，且需採用放電加工製造模穴，導致有製造時間長，且成本偏高的缺點。
- A mechanical press type of electric igniter introduced in this paper, with originality in the structure design, is a kind of electromechanical initiation equipment. 該文介紹的機械壓力式電起爆器在結構設計上具有獨到之處，是一種機電一體化起爆裝置。
- This paper introduced the inserted forging die,and the difficult point of its plasticity design. The main point of its plasticity design which can enlarge its function. 簡要地介紹了鑲塊鍛模結構特點和可塑性優化設計的難點;著重介紹擴大其使用性能可塑性設計方法的要點.
- COMPOSITION OF THE LINE :Recoiler 、staightener unit、feeder、swing unit、mechanical press、stacking system、hydraulic system、electric control system、etc. 主要組成設備：開卷機、校平機、送料機、擺動單元、專用閉式單點機械壓力機、碼垛裝置、液壓系統、電氣控制系統等。
- The life of H13 steel forging die for link was studied,the relation of die life and die rigidity was discussed, the measures of increasing die life were brought forward. 研究了H13鋼連桿鍛模的壽命問題,討論了模具壽命與模具硬度的關係,提出了提高模具壽命的措施,設計了H13鋼連桿鍛模的最佳熱處理工藝。
- Common problems consisting in the slide position control in the current mechanical press are discussed, and the feasibility of using the iterative learning method is analyzed. 討論了目前機械壓力機滑塊位置控制中普遍存在的問題,分析了迭代學習方法在壓力機滑塊位置控制中應用的可行性。
- Analysis on forging technolgy of transverse arm part has been introduced, upon which technics flow of die forging has been designed, with design of forging die cavity. 通過對轎車左右橫臂的結構及鍛造工藝分析,制定了其模鍛工藝流程,介紹了模鍛工藝及其工步型腔設計。
