您要查找的是不是:
- It was hard, hot work getting through the jungle. 通過密林既難又炎熱。
- Obtain hot work permit prior to commencing work. 開工前必須申請動火許可證。
- Hot work will be permitted only if the LEL is <10%. 只有讀數小於10%25的爆炸極限,才能進行動火作業操作。
- The results show that the work hardening rate of pure tantalum is low. 研究結果表明:純鉭的宏觀加工硬化速率比較低。
- Get a Work Permit before you can start the hot work. 辦理作業許可證才能進行動火作業。
- MISO option uses the von Mises yield criteria coupled with an isotropic work hardening assumption. 幫助中的小應變分析和大應變分析具體是指什麼情況?
- HAYNES HR120 alloy cutting performance is bad and isvery sensitive to the work hardening. HAYNESHR120合金切削性能差,對加工硬化很敏感。
- DP steel has better work hardening ability while TRIP steel has better bake hardening ability. DP鋼擁有更加優良的加工硬化能力,TRIP鋼則具有較為理想的烘烤硬化能力。
- A hot work permit must be obtained to enter a process unit with a vehicle. 駕駛車輛進入工藝單元時應另外再辦理一份工作準證。
- The simulation results suggest that Bauschinger effect and work hardening etc are validated in the model. 模擬結果表明,彎曲過程中存在鮑辛格效應和加工硬化等現象。
- The work hardening rate of pure tantalum was studied by tension test, optical microscope and TEM. 摘要藉助力學性能實驗、金相顯微鏡和透射電鏡等手段研究了純鉭的加工硬化速率。
- It was hot work, so after an hour we plunked ourselves down in a shade. 這是高溫作業,所以一小時后我們找了一塊陰涼地一屁股坐下去了。
- The fracture appearances transfer from dimple to intercrystalline fracture with the temperature drops and cleavage fracture appear when work hardening happened. 衝擊斷口由室溫下的韌窩斷口逐漸轉化為低溫下的沿晶斷口,在加工硬化時還會出現解理斷口。
- Above 293K,the changes of CRSS (critical resolved shear stre s)and work hardening behavior with temperature were ecided by the K-W locking etc. 而溫度高於293K,K-W鎖等決定了欠時效態的形變硬化行為;
- The yield strength of JCOE welded pipe was different from the mother steel plate because of the influence of Bauschinger effect and work hardening. 摘要由於包辛格效應和加工硬化的影響,JCOE制管后相對所採用鋼板管體屈服強度會發生變化。
- The work hardening models are built.The effect of the coefficient of friction and the deforming ratio on the process of ironing is analyzed. 在考慮加工硬化的基礎上分析了凹模、芯軸與製件之間的摩擦因子以及變形比對變薄拉深工藝過程的影響。
- The research shows that work hardening is large at the broaching surface depth and the main factor affecting broaching HSS tool wear. 試驗結果表明:拉削表層加工硬化程度和深度都較大;是高速鋼拉刀磨損的主要原因。
- The navigation deck is not plain, we will fair the deck by hot working. 駕駛甲板不平,我們要火工校正。
- Adequate air supply must be provided as hot work will deplete oxygen content in the confine space. 應確保提供足夠的空氣,因為動火工作會消耗封閉空間的氧氣。
- Explicit finite element method DYNAFORM was used for simulation of the deep drawing process of the square boxes.Anisotropy and work hardening were considered. 用顯式有限元軟體DYNAFORM進行了模擬分析,考慮了各向異性和加工硬化。