您要查找的是不是:
- The upper horizontal part of a step in a staircase. 踏步板樓梯中一個台階上的水平的上部
- Parting line at the acceptable surface. 合模分佈在合理可接受的表面。
- Subdivide with a horizontal parting below the occipital. 在後頭骨下面以水平線分別細分。
- Parting line cleared and released properly? 分模線是否正確?
- Poultry Slaughtering and Processing Line: Horizontal Parting Saw Band Saw apron Washer Laser Parting Saw Spiral Picking platform and so on. 家禽線:家禽屠宰生產線:卧式分段鋸,帶式鋸骨鋸,圍裙清洗器,激光式分段鋸,旋轉分檢台。
- Parting line locks are required on all molds. 瑣模塊所有的模具都需要。
- Moulding machines, Moulding line, Vertical parting automatic shooting moulding line, Horizontal parting stripper shooting moulding line, Sand preparation system Resin sand line, Silicate-bonded sand line. Shot blaot cleaning equipment, Surface. 造型機,造型線,垂直分型、水平分型自動造型線,砂處理成套設備,樹脂砂、水玻璃砂成套設備,中英合資拋丸清理機、表面強化設備。
- The parting line tolerance for gib installation is +.000/-.002. 安裝導板的分模線公差為+.;000/-
- Also the thinnest part will not be on the most horizontal parts. 同樣的,筆畫最細的部分也不是位於水平方向上。
- A plain or decorated horizontal part of an entablature between the architrave and cornice. 檐壁上橫樑中在框掾和額板之間簡易或有裝飾的水平部位
- Immobility time in tail suspension test referred to the sum of horizontal part of the activity curve in 6 minutes on computer. 懸尾實驗「不動時間」以計算機上小鼠活動曲線在6min內呈直線部分的累計之和。
- Particularly, it is the first time that the role of the horizontal part of Coriolis force played in the propagation of internal waves was studied. 首次研究了科氏力水平分量對內波傳播的影響。
- The horizontal part of the Coriolis force suppressed the nonlinearity of internal waves; and the wavelength was broadened. 科氏力水平分量抑制內波的非線性效應,使得內波變緩,振幅減小。
- There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 產品的這個位置不能出模,我們打算做行位,在此面上會有分模線,你接受嗎?
- The horizontal part of the Coriolis force suppressed the nonlinearity of internal waves;and the wavelength was broadened. 科氏力水平分量抑制內波的非線性效應,使得內波變緩,振幅減小。
- Becasue of hand deflashing, please mark the parting line into the drawing, and please let me know then the flash size. 因為手遮光,請將分界線在圖中標出來,並告訴確切尺寸。
- The vertical line meets the horizontal one here. 垂直線與水平線在此相交。
- How to select the proper different pressure of UBD in the horizontal part of the well was discussed in this paper,as well the design of foam parameter. 著重論述了水平井段欠平衡鑽井負壓差值的選擇依據,以及泡沫流體各參數的設計方法。
- Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate part line locks. 上、下模需要精確配合或有擦位的地方,模具一定要有直身鎖。
- The parting line at ends of block should be designed such that any offset is in 1"increments for maintenance purposes on core. 考慮到動模維護需要,封膠面應有1」左右的偏移增量。