您要查找的是不是:
- The dynamic stress concentration problems at the swallowtail on a hammer forging die are investigated by using the dynamic photoelastie method. 用動態光彈性法研究了錘鍛模燕尾的動態應力集中問題。
- So it is significative to study the ICAD system of hammer forging dies for connection rods. 因此,連桿錘鍛模ICAD系統的研究就有了重要的意義。
- Optimization expert system of hammer forging die materials 錘鍛模具材料優化專家系統
- Study on 3D CAD System of Hammer Forging Die for Carriage Forging 客車鍛件錘鍛模三維CAD系統的研製
- PHOTOELASTIC STUDY OF DYNAMIC STRESS CONCENTRATION AT SWALLOWTAIL ON HAMMER FORGING DIE 錘鍛模燕尾動態應力集中的光彈性研究
- Development of the 3D CAD System for the Hammer Forging Die for the Forged Parts of Buses 客車常用鍛件錘鍛模三維CAD系統的研製
- 2.So it is significative to study the ICAD system of hammer forging dies for connection rods. 因此,連桿錘鍛模ICAD系統的研究就有了重要的意義。
- Design of a Composite Hot Forging Die for Screw Plugs. 油孔螺塞拼接式熱鍛模具的設計
- The hammer forging process of TC6 titanium alloy clasp has been simulated by using rigid-viscoplastic FEM. 在TC6鈦合金卡環的高溫錘鍛過程中,模具承受非常大的應力。
- Design, construction and using of a gas heating furnace for hammer forging have been introduced. 介紹了一台鍛錘用煤氣加熱爐的設計、施工及使用情況。
- Die blocks for closed-die hammer forging 鍛錘用模具坯料
- Abstract The paper gives out structure of tilting pin type hydraulic forging die for producing frame of shaker. 給出了震動器機殼斜銷式液鍛模具設計結構。
- Through the analysis of hook, a reasonable forging process and forging die have been designed. The defects has been analyzed and solved. 摘要通過對吊鉤的工藝分析,設計了合理的鍛造工藝方案及其熱鍛模,並對出現的缺陷進行了分析解決。
- An investigation was carried out for the recondition of a mould for the forming of automotive plastic floor board and a half-axle swing forging die. 介紹了幾種典型模具快速修復工藝方法,並對汽車地板革成形模和汽車半軸擺動輾壓模的修復進行了研究。
- Traditional forging die manufacturing including a lot of process and using EOM to form the impression results some disadvantages such as longer production time and higher cost. 摘要傳統鍛模加工,由於加工道次多,且需採用放電加工製造模穴,導致有製造時間長,且成本偏高的缺點。
- This paper introduced the inserted forging die,and the difficult point of its plasticity design. The main point of its plasticity design which can enlarge its function. 簡要地介紹了鑲塊鍛模結構特點和可塑性優化設計的難點;著重介紹擴大其使用性能可塑性設計方法的要點.
- The life of H13 steel forging die for link was studied,the relation of die life and die rigidity was discussed, the measures of increasing die life were brought forward. 研究了H13鋼連桿鍛模的壽命問題,討論了模具壽命與模具硬度的關係,提出了提高模具壽命的措施,設計了H13鋼連桿鍛模的最佳熱處理工藝。
- Analysis on forging technolgy of transverse arm part has been introduced, upon which technics flow of die forging has been designed, with design of forging die cavity. 通過對轎車左右橫臂的結構及鍛造工藝分析,制定了其模鍛工藝流程,介紹了模鍛工藝及其工步型腔設計。
- CAD of finishing cavity for hammer forging 錘上模鍛終鍛型槽的計算機輔助設計