您要查找的是不是:
- It has locknut fasten rotor to a spindle. 配有防松螺母固定轉子與中心軸。
- Position locknut over top of fuel pump module. 將鎖定螺帽放在燃油泵模組上。
- Thank you,Freewheel ,for your enjoyable writings! 後生可畏;後生可賀!
- Tighten locknut 1 to fix the thread stand. 擰緊固定螺母1不讓線架裝置鬆動。
- Level3: Tolerance matching of freewheel bushings. Factory only. 級別3:飛輪軸套的公差矯正。只有工廠可以操作。
- SunTour's 1980 New Winner freewheel offered complete flexibility. 山圖的1980年新的優勝者飛輪提供全面的靈活性。
- Recheck clearance on all valves again after locknut is tightened. 防松螺母擰緊后,再對所有氣門的間隙重新檢查一次。
- CKZ series freewheel is shielded by shield bearings on both ends. CKZ型為內含兩套軸承支撐的楔塊式超越離合器。
- Secure with locknut and gaskets. Install valve assembly. 用放鬆螺母和墊圈緊固。安裝閥門總成。
- Type CK-B is a sprag type freewheel non-bearing supported.Nominal dia. CK-B系列為無軸承支撐外環兩端面帶鍵槽的楔塊式單向離合器。
- Tighten left axle-end, insert freewheel (without pawls), tighten right axleend. 鎖緊左側的軸端蓋子,插入花鼓本體(沒有棘爪),鎖緊右側的軸端蓋子。
- The valve is mainly made up of handle, body, disc, locknut and seal etc. 手動密閉閘閥主要由把手、閥體、插板、鎖緊螺釘、密封裝置等部件組成。
- Run sway the drift charging vehicle video frequency for my freewheel! 給我一個飛輪跑跑搖控車的漂移視頻!
- To replace seat/ stem module shut off supply, loosen locknut and back off adjusting screw. 要更換閥座/桿模塊,先關閉供應管道,鬆開鎖緊螺母,退出調節螺絲。
- To replace seat/stem module shut off supply, loosen locknut and back off adjusting screw. 要更換閥座/閥桿模塊,先關閉供應管道,鬆開鎖緊螺母,退出調節螺絲。
- Type GC-D is a roller type freewheel non-bearing supported, Earrings are required to support axial and radial loads. GC-D系列為無軸承支撐滾柱式單向離合器。
- Output flange is connected with output shaft by a involute spline, and fastened by a locknut. 輸出突緣通過漸開線花鍵與輸出軸相連,並用鎖緊螺母將其鎖住。
- SunTour also made a combined freewheel plus rear hub, called Unit-Hub, in 1969 for small wheel bicycles. 山圖也發了聯合飛輪加上後輪,稱為股樞紐於1969年,小輪自行車。
- Use an open-end wrench and open the locknut on the accumulator valve assembly two or threefull turns. 使用開口扳手,打開蓄能器閥門上的防松螺栓-----------。
- This was the beginning of the Japanese derailleur and multi-sprocket freewheel industry. 這是日本變速器和多開始,鏈輪,飛輪產業。