您要查找的是不是:
- Tubular copper body creates smooth flow path and low headloss. 管狀銅閥體形成流暢的流道,也降低了水頭損失。
- Flow Path Reformation of 200 MW Steam Turbines in Xingtai Power Generation Co. Ltd. 興泰發電有限責任公司200MW機組通流部分改造。
- Only one conduction loss of the power switch is present in the power flow path during the inversionperiod. 逆變時,在功率通量迴路中只有一個功率開關上有傳導損耗。
- Body ? streamlined flow path minimizes pressure drop. Butt weld, venturi or flanged ends provide piping alternatives. 閥體?流線形流道,最大限度減少壓降。對焊、縮喉管或法蘭連接埠幾種可供選擇的連接方式。
- It has such characteristics as easy control,little flow path,simple reprocess and high yield etc. 合成過程為動態連續反應,具有反應易控、流程短、后處理簡便、收率高等特點。
- In this paper, tne manufactured process flow path of TAN is investigated and its econom-ical benefit is also analyzed. 本文探討了間三氟甲基苯乙腈(TAN)的生產工藝流程,並對其經濟效益進行了分析。
- It described a special design method using virtual fabricate microsystem to realize microsystem design and supplying a flow path to design microsystem. 介紹了微系統專用的設計方法;即虛擬製造微系統來實現微系統的設計;並提供了微系統設計流程.
- The energy flow path, the energy flow sources and sinks of laminated composite plates can be identified for different loading cases and boundary conditions. 從結構聲強向量圖和流線圖可獲得關於能量傳遞路徑、源位置和能量匯合點的許多信息。
- The polyamide to easy generation salivate (PA) , through choosing form of a powerful person hot nozzle also can realize hot flow path to shape. 對易產生流涎的聚醯胺(PA),通過選用閥式熱噴嘴也能實現熱流道成型。
- The flow path of injected water is independent on the absolute permeability, but on the relative permeability value between layers?. 注入水自然流動形成的通道不完全是由絕對滲透率決定,而與層位之間滲透率相對大小有關。
- BLUSH: Discoloration or change in gloss, generally appearing at gates, abrupt thickness changes, or other structures along flow path. 輕微裉色:變色或光澤度變化;一般出現在注入口上;厚度突變處;或是其他流程中的結構.
- Expatiate water-cycling mode for large CFB hot-water boiler、water flow path and heat-exchanger surface structural design. 闡述了大型循環流化床熱水鍋爐的水循環方式、水流程及受熱面結構設計布置。
- The outer mechanical seal shall be located in a recessed housing outside the main flow path of the pump to avoid damage. 外置機械式密封應該位於泵主流道以外的凹式箱體內,以避免受到破壞。
- In liquid composites molding(LCM) processes,a gap between the perform and the mold edge can create a preferential flow path for the resin, which is the so-called edge effect. 在複合材料液體模塑成型工藝中(LCM),預成型體和模具壁間存在的縫隙容易產生優先的樹脂流道,即為常見的邊緣效應。
- The emitter adopts unique design of circular arc flow path and has the characteristics of complete turbulent fluid, automatic washing and strong antiblocking. 滴頭採用圓弧寬流道的獨特設計,全紊流、自沖洗、抗阻塞能力強。
- The flow path,main equipment,design calculation and running situation of 72 wt% flake caustic soda production plant equiped with film evaporator were introduced. 介紹了薄膜蒸發器配套用72%25片鹼生產裝置的工藝流程、主要設備、設計計算和使用情況。
- The uprating of a steam turbine power output will necessitate the increase in area of the turbine last-stage flow path and an enhancement in blade corrosion-resistance. 增大汽輪機的單機功率,就要求增大其末級通流部分尺寸和葉片的抗腐蝕性能。
- In liquid composites molding(LCM) processes, a gap between the perform and the mold edge can create a prefer ential flow path for the resin, which is the so-called edge effect. 摘要在複合材料液體模塑成型工藝中(LCM),預成型體和模具壁間存在的縫隙容易產生優先的樹脂流道,即為常見的邊緣效應。
- If plant air or electric is restored, the pilot or solenoid resets, flow path is restored and the volume tank gradually fills with air which is locked in with a check valve. 當主氣源或電源恢復正常,則導閥或電磁閥就重新設置,罐內氣體重新加註,充滿后配置的止回閥將關斷氣源流徑,而將氣體儲存在備用氣源罐內。
- This paper discussed the design criteria of material selection,the area of single unit,flow path,flow rate of a plate heat exchanger (PHE)in a geothermal heating system. 重點分析了板式換熱器在地熱供暖系統中材料、單片面積、流程、流道、流體流速等選取的原則;在綜合考慮技術、經濟、環境效益及節能的基礎上,論述了對板式換熱器優化設計的方法。