您要查找的是不是:
- Reattach the relief valve hose to the elbow in the bottom flange cover. 重新將安全閥軟管接到底部法蘭蓋內的彎頭上。
- The injection mould for a duplicator cover plate is designed. 設計了複印機蓋板的注塑模具。
- Reattach cover plate to make an air and water tight seal. 重新固定蓋板,並緊密密封防止空氣和水通過。
- Bolted cover plate to protect seal and cylinder from the ingress of debris. 上蓋板可防止雜物進入缸筒損壞密封。
- Disconnect the relief valve hose from the elbow in the bottom flange cover at the swivel hose connection. Do not remove the elbow. 從底部法蘭蓋內的旋轉軟管連接彎頭上斷開安全閥。不要拆卸彎頭。
- Disconnect the hose from the bottom cover plate to the relief valve. 斷開底部蓋板到安全閥上的軟管。
- Remove the four bottom bolts from the bottom of the relief valve assembly with a 5/16" socket or open-end wrench. Remove the bottom flange cover. 用一把5/16英寸套筒扳手或開口扳手從安全閥總成底部拆卸四個底部螺栓。拆卸底部法蘭蓋。
- Position the bottom flange cover on the bottom of the relief valve body and secure by hand tightening the four bottom bolts. 將底部法蘭蓋放在安全閥閥體底部上,用手旋緊四個底部螺栓加以緊固。
- Remove the cover plate of the relief valve by removing the four connecting screws. 通過拆卸四個連接螺絲來拆卸安全閥蓋板。
- If you open the cover plate of your cell phone, you'll see a rectangular LCD on its backside. 把手機的蓋板打開來,背面就是一整片長方形的液晶螢幕。
- Before installing cover plate, a continuity test should be performed to assure that switches are properly set. 在安裝蓋板之前,應該進行斷路檢查測試,以確保開關正確設置。
- Adjust the Mounting Bracket so that the Sensor sits flush against the Cover Plate. 請調整安裝架使得感應器與蓋板處於合適的位置。
- Fitting 272 has an opening 274 therethrough that communicates with channel 266 and recess 264 in cover plate 262. 管接頭272有一通道274經過,連通蓋板262上的通道266與凹處264。
- Slowly open all ball valves to relieve air and water pressure. Loosen bolts on groove coupler and remove groove coupler and cover plate from valve body. 慢慢開啟所有球閥,釋放空氣和水壓力。鬆懈溝槽狀聯結器上的螺栓,從閥體上拆卸溝槽狀聯結器和閥蓋板。
- Slowly open all ball valves to relieve air and water pressure. Loosen bolts on groove coupler and remove groove couple and cover plate from valve body. 慢慢開啟所有球閥,釋放空氣和水的壓力。鬆開溝槽連接器上的螺栓,從閥體上拆卸溝槽連接器和蓋板。
- Cover plate 262 includes outwardly extending lugs 278 that are dimensioned to be in registry with lugs 258 on valve body 212. 蓋板262也含有向外凸出的柄座(lug)278來接上閥體212上的柄座258。
- In this respect, cover plate 262 has a planar surface 276 dimensioned to mate with planar surface 234 of valve body 212. 就這方面來說,蓋板262有一平面276設計成能與閥體212上的平面234密合。
- According to the NHTSA's Web site, the recall is due to a faulty drive shaft cover plate that could lead to a detached drive shaft. 根據美國國家公路交通安全局的網站,此次召回是由於錯誤的傳動軸蓋板可能導致脫離傳動軸。
- Products: Engineering series of ditch cover plate, automobile castings all kinds of casting used for the mechanical, sanitary equipment series of casting. 工程用系列地溝蓋板、汽車配件、機械用各種鑄件、生活用品系列鑄件。
- The front cover of the novel has been torn off. 這本小說的封面已被撕掉。