您要查找的是不是：
- Essential elements of drill hole. 鑽孔具有的結構和尺寸因素。
- Should Drill hole on the fuselage reinforcing plate. 要鑽在機身的加強層板上。
- He broached out the drilled hole. 他鑿大鑽孔。
- Most darts are marked with notches for the dart site and drill hole for the point at which the dart terminates. 大多數省道用刀眼作為省道定位標記,用鑽眼表示省道終端。
- The plastic hose should have the correct external diameter in relation to the drill hole. 塑料軟管的外徑應該與炮眼直徑相適應。
- The fact that the drill hole openings are located under water complicates charging work. 炮眼口位於水下，無疑會使裝葯工作複雜化。
- Measure rough dimension of drilling hole. 測量打孔珍珠大致尺寸.
- Adjust bust point. Trace off form the draft, add seam allowances. Notch and mark drill hole for dart point. 調整胸點。從樣板原圖上描下,加縫份。打刀眼並標出省端點的鑽孔位置。
- Match the balance marks carefully and complete by tapering the stitching past the drill hole in the usual way. 仔細地對準對位記號並用以往的方法完成。針跡逐漸變細經過鑽眼即可。
- B, QuickAnchor (Mitek) suture anchor consists of hook device with suture that is anchored into drill hole in bone. 為此已有用同種異體皮質骨製成的商用螺釘。
- Levelling is usually carried out with vertical drill holes. 整平爆破通常用垂直炮眼進行。
- First drill hole and cut across a bit bottom board,then pour starch into consolidate bottom board. 在井下施工堵水鑽孔,鑽孔穿透煤層隔水底板少許,注漿堵水加固底板。
- All of the gems are cabochon;the manufacture technique is developed in terms of cat's-eye and the drill hole. 幾乎所有的寶石主要為弧面型，具特殊光學效應的寶石的加工以及寶石的鑽孔技術已達相當高的水平。
- The unit clamp design including bores the jig design, the milling jig design, the drill hole jig design and so on. 專用夾具的設計包括鏜孔夾具設計、銑槽夾具設計、鑽孔夾具設計等。
- They drill holes in the ice and drive light trucks over them. 他們在冰路上鑽一些洞，然後駕駛輕型貨車在路上開過。
- To drill holes in a mirror, you need a special mirror drill bit. 在鏡子上鑽孔，你需要一個特殊的鏡子鑽頭。
- Since the crater-hole breakage is of great importance, it can be advisable to use a larger drill hole than the others in the raise. 由於漏斗炮眼的爆破效果非常重要，故天井爆破宜採用較大的炮眼直徑。
- The anchorage force of consolidated anchorage with prestressed bolt is actually the friction resistance between sand and the wall of drill hole. 砂固結預應力錨桿的錨固力是由砂體與錨孔壁之間的摩擦力提供的。
- Stitch the dart, clearing the drill hole by approximately 2mm and gradually running off the folded edge about 1cm below the drill hole, run a chain of stitching. 越過定位點大約2mm,緝縫省道,並逐漸地在定位點下面1cm處"留出"折邊,最後縫一連串的線跡結束。
- The transient electromagnetic thchniques can be used to determine the key region for grouting reconstruction, guiding the drill hole layout and detect the grouting effect. 利用瞬變電磁技術探測煤層底板含水層的賦水性特徵，確定工作面內注漿改造重點區域，指導鑽孔布置，並在底板改造后檢驗注漿改造效果。
